ESP32 & ESPHome Voice Assistant

esp32-voice.yaml

esphome:
  name: esp32-mic-speaker
  friendly_name: esp32-mic-speaker
  on_boot:
     - priority: -100
       then:
         - wait_until: api.connected
         - delay: 1s
         - if:
             condition:
               switch.is_on: use_wake_word
             then:
               - voice_assistant.start_continuous:

esp32:
  board: esp32dev
  framework:
    type: esp-idf
    version: recommended

# Enable logging
logger:

# Enable Home Assistant API
api:

ota:

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Esp32-Mic-Speaker"
    password: "9vYvAFzzPjuc"

i2s_audio:
  i2s_lrclk_pin: GPIO27
  i2s_bclk_pin: GPIO26

microphone:
  - platform: i2s_audio
    id: mic
    adc_type: external
    i2s_din_pin: GPIO13
    pdm: false

speaker:
  - platform: i2s_audio
    id: big_speaker
    dac_type: external
    i2s_dout_pin: GPIO25
    mode: mono

voice_assistant:
  microphone: mic
  use_wake_word: false
  noise_suppression_level: 2
  auto_gain: 31dBFS
  volume_multiplier: 2.0
  speaker: big_speaker
  id: assist

switch:
  - platform: template
    name: Use wake word
    id: use_wake_word
    optimistic: true
    restore_mode: RESTORE_DEFAULT_ON
    entity_category: config
    on_turn_on:
      - lambda: id(assist).set_use_wake_word(true);
      - if:
          condition:
            not:
              - voice_assistant.is_running
          then:
            - voice_assistant.start_continuous
    on_turn_off:
      - voice_assistant.stop
      - lambda: id(assist).set_use_wake_word(false);

Working config (2025.5.0) with two INMP441 mic and PCM5102A stereo dac base on voice pe

substitutions:
  device_name: "esp32s3"
  friendly_name: "esp32s3"
  device_description: "esp32s3 VA test"
  # Phases of the Voice Assistant
  # The voice assistant is ready to be triggered by a wake word
  voice_assist_idle_phase_id: '1'
  # The voice assistant is waiting for a voice command (after being triggered by the wake word)
  voice_assist_waiting_for_command_phase_id: '2'
  # The voice assistant is listening for a voice command
  voice_assist_listening_for_command_phase_id: '3'
  # The voice assistant is currently processing the command
  voice_assist_thinking_phase_id: '4'
  # The voice assistant is replying to the command
  voice_assist_replying_phase_id: '5'
  # The voice assistant is not ready
  voice_assist_not_ready_phase_id: '10'
  # The voice assistant encountered an error
  voice_assist_error_phase_id: '11'
  # Change this to true in case you ahve a hidden SSID at home.
  hidden_ssid: "false"


esphome:
  name: '${device_name}'
  comment: '${device_description}'
  min_version: 2025.5.0
  on_boot:
    priority: 375
    then:
      # Run the script to refresh the LED status
      - script.execute: control_leds
      - delay: 1s
      # If after 10 minutes, the device is still initializing (It did not yet connect to Home Assistant), turn off the init_in_progress variable and run the script to refresh the LED status
      - delay: 10min
      - if:
          condition:
            lambda: return id(init_in_progress);
          then:
            - lambda: id(init_in_progress) = false;
            - script.execute: control_leds

esp32:
  board: esp32-s3-devkitc-1
  cpu_frequency: 240MHz
  variant: esp32s3
  flash_size: 16MB
  framework:
    type: esp-idf
    version: recommended
    sdkconfig_options:
      CONFIG_ESP32S3_DATA_CACHE_64KB: "y"
      CONFIG_ESP32S3_DATA_CACHE_LINE_64B: "y"
      CONFIG_ESP32S3_INSTRUCTION_CACHE_32KB: "y"

      # Moves instructions and read only data from flash into PSRAM on boot.
      # Both enabled allows instructions to execute while a flash operation is in progress without needing to be placed in IRAM.
      # Considerably speeds up mWW at the cost of using more PSRAM.
      CONFIG_SPIRAM_RODATA: "y"
      CONFIG_SPIRAM_FETCH_INSTRUCTIONS: "y"

      CONFIG_BT_ALLOCATION_FROM_SPIRAM_FIRST: "y"
      CONFIG_BT_BLE_DYNAMIC_ENV_MEMORY: "y"

      CONFIG_MBEDTLS_EXTERNAL_MEM_ALLOC: "y"
      CONFIG_MBEDTLS_SSL_PROTO_TLS1_3: "y"  # TLS1.3 support isn't enabled by default in IDF 5.1.5
  
psram:
  mode: octal
  speed: 80MHz

wifi:
  id: wifi_id
  fast_connect: ${hidden_ssid}
  on_connect:
    - lambda: id(improv_ble_in_progress) = false;
    - script.execute: control_leds
  on_disconnect:
    - script.execute: control_leds
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: '${device_name}'
    password: !secret fallback_password

# Enable Home Assistant API
api:
  id: api_id
  on_client_connected:
    - script.execute: control_leds
  on_client_disconnected:
    - script.execute: control_leds
  encryption:
    key: !secret !secret api_key_esp32s3

ota:
  - platform: esphome
    id: ota_password
    password: !secret ota_password

# avoids logging debug sensor updates
logger:
  level: DEBUG
  logs:
    sensor: WARN

time:
  - platform: homeassistant
    id: homeassistant_time

text_sensor:
  # Send IP Address
  - platform: wifi_info
    ip_address:
      name: $friendly_name IP Address
    
globals:
  # Global index for our LEDs. So that switching between different animation does not lead to unwanted effects.
  - id: global_led_animation_index
    type: int
    restore_value: no
    initial_value: '0'
  # Global initialization variable. Initialized to true and set to false once everything is connected. Only used to have a smooth "plugging" experience
  - id: init_in_progress
    type: bool
    restore_value: no
    initial_value: 'true'
  # Global variable storing the state of ImprovBLE. Used to draw different LED animations
  - id: improv_ble_in_progress
    type: bool
    restore_value: no
    initial_value: 'false'
  # Global variable tracking the phase of the voice assistant (defined above). Initialized to not_ready
  - id: voice_assistant_phase
    type: int
    restore_value: no
    initial_value: ${voice_assist_not_ready_phase_id}
  # Global variable tracking if the dial was recently touched.
  - id: dial_touched
    type: bool
    restore_value: no
    initial_value: 'false'
  # Global variable tracking if the LED color was recently changed.
  - id: color_changed
    type: bool
    restore_value: no
    initial_value: 'false'
  # Global variable tracking if the jack has been plugged touched.
  - id: jack_plugged_recently
    type: bool
    restore_value: no
    initial_value: 'false'
  # Global variable tracking if the jack has been unplugged touched.
  - id: jack_unplugged_recently
    type: bool
    restore_value: no
    initial_value: 'false'
  # Global variable storing the first active timer
  - id: first_active_timer
    type: voice_assistant::Timer
    restore_value: false
  # Global variable storing if a timer is active
  - id: is_timer_active
    type: bool
    restore_value: false
  # Global variable storing if a factory reset was requested. If it is set to true, the device will factory reset once the center button is released
  - id: factory_reset_requested
    type: bool
    restore_value: no
    initial_value: 'false'

switch:
  - platform: restart
    name: $friendly_name Restart

  # This is the master mute switch. It is exposed to Home Assistant. The user can only turn it on and off if the hardware switch is off. (The hardware switch overrides the software one)
  - platform: template
    id: master_mute_switch
    restore_mode: RESTORE_DEFAULT_OFF
    icon: "mdi:microphone-off"
    name: Mute
    entity_category: config
    lambda: |-
      // Muted either if the hardware mute switch is on or the microphone's software mute switch is enabled
      if (id(hardware_mute_switch).state || id(i2s_mics).get_mute_state()) {
        return true;
      } else {
        return false;
      }
    turn_on_action:
      - if:
          condition:
            binary_sensor.is_off: hardware_mute_switch
          then:
            - microphone.mute:
    turn_off_action:
      - if:
          condition:
            binary_sensor.is_off: hardware_mute_switch
          then:
            - microphone.unmute:
    on_turn_on:
      - script.execute: control_leds
    on_turn_off:
      - script.execute: control_leds
  # Wake Word Sound Switch.
  - platform: template
    id: wake_sound
    name: Wake sound
    icon: "mdi:bullhorn"
    entity_category: config
    optimistic: true
    restore_mode: RESTORE_DEFAULT_ON
  # Internal switch to track when a timer is ringing on the device.
  - platform: template
    id: timer_ringing
    optimistic: true
    internal: true
    restore_mode: ALWAYS_OFF
    on_turn_off:
      # Disable stop wake word
      - micro_wake_word.disable_model: stop
      - script.execute: disable_repeat
      # Stop any current annoucement (ie: stop the timer ring mid playback)
      - if:
          condition:
            media_player.is_announcing:
          then:
            media_player.stop:
              announcement: true
      # Set back ducking ratio to zero
      - mixer_speaker.apply_ducking:
          id: media_mixing_input
          decibel_reduction: 0
          duration: 1.0s
      # Refresh the LED ring
      - script.execute: control_leds
    on_turn_on:
      # Duck audio
      - mixer_speaker.apply_ducking:
          id: media_mixing_input
          decibel_reduction: 20
          duration: 0.0s
      # Enable stop wake word
      - micro_wake_word.enable_model: stop
      # Ring timer
      - script.execute: ring_timer
      # Refresh LED
      - script.execute: control_leds
      # If 15 minutes have passed and the timer is still ringing, stop it.
      - delay: 15min
      - switch.turn_off: timer_ringing

binary_sensor:
  # Center Button. Used for many things (See on_multi_click)
  - platform: gpio
    id: center_button
    pin:
      number: GPIO0
      inverted: true
    on_press:
      - script.execute: control_leds
    on_release:
      - script.execute: control_leds
      # If a factory reset is requested, factory reset on release
      - if:
          condition:
            lambda: return id(factory_reset_requested);
          then:
            - button.press: factory_reset_button
    on_multi_click:
      # Simple Click:
      #   - Abort "things" in order
      #     - Timer
      #     - Announcements
      #     - Voice Assistant Pipeline run
      #     - Music
      #   - Starts the voice assistant if it is not yet running and if the device is not muted.
      - timing:
          - ON for at most 1s
          - OFF for at least 0.25s
        then:
          - if:
              condition:
                lambda: return !id(init_in_progress) && !id(color_changed);
              then:
                - if:
                    condition:
                      switch.is_on: timer_ringing
                    then:
                      - switch.turn_off: timer_ringing
                    else:
                      - if:
                          condition:
                            voice_assistant.is_running:
                          then:
                            - voice_assistant.stop:
                          else:
                            - if:
                                condition:
                                  media_player.is_announcing:
                                then:
                                  media_player.stop:
                                    announcement: true
                                else:
                                  - if:
                                      condition:
                                        media_player.is_playing:
                                      then:
                                        - media_player.pause:
                                      else:
                                        - if:
                                            condition:
                                              and:
                                                - switch.is_off: master_mute_switch
                                                - not:
                                                    voice_assistant.is_running
                                            then:
                                              - script.execute:
                                                  id: play_sound
                                                  priority: true
                                                  sound_file: !lambda return id(center_button_press_sound);
                                              - delay: 300ms
                                              - voice_assistant.start:
      # Double Click
      #  . Exposed as an event entity. To be used in automations inside Home Assistant
      - timing:
          - ON for at most 1s
          - OFF for at most 0.25s
          - ON for at most 1s
          - OFF for at least 0.25s
        then:
          - if:
              condition:
                lambda: return !id(init_in_progress) && !id(color_changed);
              then:
                - script.execute:
                    id: play_sound
                    priority: false
                    sound_file: !lambda return id(center_button_double_press_sound);
                - event.trigger:
                    id: button_press_event
                    event_type: "double_press"
      # Triple Click
      #  . Exposed as an event entity. To be used in automations inside Home Assistant
      - timing:
          - ON for at most 1s
          - OFF for at most 0.25s
          - ON for at most 1s
          - OFF for at most 0.25s
          - ON for at most 1s
          - OFF for at least 0.25s
        then:
          - if:
              condition:
                lambda: return !id(init_in_progress) && !id(color_changed);
              then:
                - script.execute:
                    id: play_sound
                    priority: false
                    sound_file: !lambda return id(center_button_triple_press_sound);
                - event.trigger:
                    id: button_press_event
                    event_type: "triple_press"
      # Long Press
      #  . Exposed as an event entity. To be used in automations inside Home Assistant
      - timing:
          - ON for at least 1s
        then:
          - if:
              condition:
                lambda: return !id(init_in_progress) && !id(color_changed);
              then:
                - script.execute:
                    id: play_sound
                    priority: false
                    sound_file: !lambda return id(center_button_long_press_sound);
                - light.turn_off: voice_assistant_leds
                - event.trigger:
                    id: button_press_event
                    event_type: "long_press"
      # Very important do not remove. Trust me :D
      - timing:
          # H ....
          - ON for at most 0.2s
          - OFF for 0s to 2s
          - ON for at most 0.2s
          - OFF for 0s to 2s
          - ON for at most 0.2s
          - OFF for 0s to 2s
          - ON for at most 0.2s
          - OFF for 0.5s to 2s
          # A ._
          - ON for at most 0.2s
          - OFF for 0s to 2s
          - ON for 0.2s to 2s
        then:
          - if:
              condition:
                lambda: return !id(init_in_progress);
              then:
                - light.turn_on:
                    brightness: 100%
                    id: voice_assistant_leds
                    effect: "Tick"
                - script.execute:
                    id: play_sound
                    priority: true
                    sound_file: !lambda return id(easter_egg_tick_sound);
                - delay: 4s
                - light.turn_off: voice_assistant_leds
                - script.execute:
                    id: play_sound
                    priority: true
                    sound_file: !lambda return id(easter_egg_tada_sound);
                - light.turn_on:
                    brightness: 100%
                    id: voice_assistant_leds
                    effect: "Rainbow"
                - event.trigger:
                    id: button_press_event
                    event_type: "easter_egg_press"
      # Factory Reset Warning
      #  . Audible and Visible warning.
      - timing:
          - ON for at least 10s
        then:
          - if:
              condition:
                lambda: return !id(dial_touched);
              then:
                - light.turn_on:
                    brightness: 100%
                    id: voice_assistant_leds
                    effect: "Factory Reset Coming Up"
                - script.execute:
                    id: play_sound
                    priority: true
                    sound_file: !lambda return id(factory_reset_initiated_sound);
                - wait_until:
                    binary_sensor.is_off: center_button
                - if:
                    condition:
                      lambda: return !id(factory_reset_requested);
                    then:
                      - light.turn_off: voice_assistant_leds
                      - script.execute:
                          id: play_sound
                          priority: true
                          sound_file: !lambda return id(factory_reset_cancelled_sound);
      # Factory Reset Confirmed.
      #  . Audible warning to prompt user to release the button
      #  . Set factory_reset_requested to true
      - timing:
          - ON for at least 22s
        then:
          - if:
              condition:
                lambda: return !id(dial_touched);
              then:
                - script.execute:
                    id: play_sound
                    priority: true
                    sound_file: !lambda return id(factory_reset_confirmed_sound);
                - light.turn_on:
                    brightness: 100%
                    red: 100%
                    green: 0%
                    blue: 0%
                    id: voice_assistant_leds
                    effect: "none"
                - lambda: id(factory_reset_requested) = true;

  # Hardware mute switch (Side of the device)
  - platform: gpio
    id: hardware_mute_switch
    internal: true
    pin: 
      number: GPIO3
      inverted: true
    on_press:
      # Play mute on sound only if software mute isn't enabled
      - if:
          condition:
            - switch.is_off: master_mute_switch
          then:
            - script.execute:
                id: play_sound
                priority: false
                sound_file: !lambda return id(mute_switch_on_sound);
    on_release:
      - script.execute:
          id: play_sound
          priority: false
          sound_file: !lambda return id(mute_switch_off_sound);
      - microphone.unmute:

light:
  # Hardware LED ring. Not used because remapping needed
  - platform: esp32_rmt_led_strip
    id: leds_internal
    pin: GPIO48
    chipset: WS2812
    max_refresh_rate: 15ms
    num_leds: 12
    rgb_order: GRB
    rmt_symbols: 192
    default_transition_length: 0ms
    power_supply: led_power

  # Voice Assistant LED ring. Remapping of the internal LED.
  # This light is not exposed. The device controls it
  - platform: partition
    id: voice_assistant_leds
    internal: true
    default_transition_length: 0ms
    segments:
      - id: leds_internal
        from: 7
        to: 11
      - id: leds_internal
        from: 0
        to: 6
    effects:
      - addressable_lambda:
          name: "Waiting for Command"
          update_interval: 100ms
          lambda: |-
            auto light_color = id(led_ring).current_values;
            Color color(light_color.get_red() * 255, light_color.get_green() * 255,
                  light_color.get_blue() * 255);
            for (int i = 0; i < 12; i++) {
              if (i == id(global_led_animation_index) % 12) {
                it[i] = color;
              } else if (i == (id(global_led_animation_index) + 11) % 12) {
                it[i] = color * 192;
              } else if (i == (id(global_led_animation_index) + 10) % 12) {
                it[i] = color * 128;
              } else if (i == (id(global_led_animation_index) + 6) % 12) {
                it[i] = color;
              } else if (i == (id(global_led_animation_index) + 5) % 12) {
                it[i] = color * 192;
              } else if (i == (id(global_led_animation_index) + 4) % 12) {
                it[i] = color * 128;
              } else {
                it[i] = Color::BLACK;
              }
            }
            id(global_led_animation_index) = (id(global_led_animation_index) + 1) % 12;
      - addressable_lambda:
          name: "Listening For Command"
          update_interval: 50ms
          lambda: |-
            auto light_color = id(led_ring).current_values;
            Color color(light_color.get_red() * 255, light_color.get_green() * 255,
                  light_color.get_blue() * 255);
            for (int i = 0; i < 12; i++) {
              if (i == id(global_led_animation_index) % 12) {
                it[i] = color;
              } else if (i == (id(global_led_animation_index) + 11) % 12) {
                it[i] = color * 192;
              } else if (i == (id(global_led_animation_index) + 10) % 12) {
                it[i] = color * 128;
              } else if (i == (id(global_led_animation_index) + 6) % 12) {
                it[i] = color;
              } else if (i == (id(global_led_animation_index) + 5) % 12) {
                it[i] = color * 192;
              } else if (i == (id(global_led_animation_index) + 4) % 12) {
                it[i] = color * 128;
              } else {
                it[i] = Color::BLACK;
              }
            }
            id(global_led_animation_index) = (id(global_led_animation_index) + 1) % 12;
      - addressable_lambda:
          name: "Thinking"
          update_interval: 10ms
          lambda: |-
            static uint8_t brightness_step = 0;
            static bool brightness_decreasing = true;
            static uint8_t brightness_step_number = 10;
            if (initial_run) {
              brightness_step = 0;
              brightness_decreasing = true;
            }
            auto light_color = id(led_ring).current_values;
            Color color(light_color.get_red() * 255, light_color.get_green() * 255,
                  light_color.get_blue() * 255);
            for (int i = 0; i < 12; i++) {
              if (i == id(global_led_animation_index) % 12) {
                it[i] = color * uint8_t(255/brightness_step_number*(brightness_step_number-brightness_step));
              } else if (i == (id(global_led_animation_index) + 6) % 12) {
                it[i] = color * uint8_t(255/brightness_step_number*(brightness_step_number-brightness_step));
              } else {
                it[i] = Color::BLACK;
              }
            }
            if (brightness_decreasing) {
              brightness_step++;
            } else {
              brightness_step--;
            }
            if (brightness_step == 0 || brightness_step == brightness_step_number) {
              brightness_decreasing = !brightness_decreasing;
            }
      - addressable_lambda:
          name: "Replying"
          update_interval: 50ms
          lambda: |-
            id(global_led_animation_index) = (12 + id(global_led_animation_index) - 1) % 12;
            auto light_color = id(led_ring).current_values;
            Color color(light_color.get_red() * 255, light_color.get_green() * 255,
                  light_color.get_blue() * 255);
            for (int i = 0; i < 12; i++) {
              if (i == (id(global_led_animation_index)) % 12) {
                it[i] = color;
              } else if (i == ( id(global_led_animation_index) + 1) % 12) {
                it[i] = color * 192;
              } else if (i == ( id(global_led_animation_index) + 2) % 12) {
                it[i] = color * 128;
              } else if (i == ( id(global_led_animation_index) + 6) % 12) {
                it[i] = color;
              } else if (i == ( id(global_led_animation_index) + 7) % 12) {
                it[i] = color * 192;
              } else if (i == ( id(global_led_animation_index) + 8) % 12) {
                it[i] = color * 128;
              } else {
                it[i] = Color::BLACK;
              }
            }
      - addressable_lambda:
          name: "Muted or Silent"
          update_interval: 16ms
          lambda: |-
            static int8_t index = 0;
            Color muted_color(255, 0, 0);
            auto light_color = id(led_ring).current_values;
            Color color(light_color.get_red() * 255, light_color.get_green() * 255,
                  light_color.get_blue() * 255);
            for (int i = 0; i < 12; i++) {
              if ( light_color.get_state() ) {
                it[i] = color;
              } else {
                it[i] = Color::BLACK;
              }
            }
            if ( id(master_mute_switch).state ) {
              it[2] = Color::BLACK;
              it[3] = muted_color;
              it[4] = Color::BLACK;
              it[8] = Color::BLACK;
              it[9] = muted_color;
              it[10] = Color::BLACK;
            }
            if ( id(external_media_player).volume == 0.0f || id(external_media_player).is_muted() ) {
              it[5] = Color::BLACK;
              it[6] = muted_color;
              it[7] = Color::BLACK;
            }
      - addressable_lambda:
          name: "Volume Display"
          update_interval: 50ms
          lambda: |-
            auto light_color = id(led_ring).current_values;
            Color color(light_color.get_red() * 255, light_color.get_green() * 255,
                  light_color.get_blue() * 255);
            Color silenced_color(255, 0, 0);
            auto volume_ratio = 12.0f * id(external_media_player).volume;
            for (int i = 0; i < 12; i++) {
              if (i <= volume_ratio) {
                it[(6+i)%12] = color * min( 255.0f * (volume_ratio - i) , 255.0f ) ;
              } else {
                it[(6+i)%12] = Color::BLACK;
              }
            }
            if (id(external_media_player).volume == 0.0f) {
              it[6] = silenced_color;
            }
      - addressable_lambda:
          name: "Center Button Touched"
          update_interval: 16ms
          lambda: |-
            if (initial_run) {
              // set voice_assistant_leds light to colors based on led_ring
              auto led_ring_cv = id(led_ring).current_values;
              auto va_leds_call = id(voice_assistant_leds).make_call();
              va_leds_call.from_light_color_values(led_ring_cv);
              va_leds_call.set_brightness( min ( max( id(led_ring).current_values.get_brightness() , 0.2f ) + 0.1f , 1.0f ) );
              va_leds_call.set_state(true);
              va_leds_call.perform();
            }
            auto light_color = id(voice_assistant_leds).current_values;
            Color color(light_color.get_red() * 255, light_color.get_green() * 255,
                  light_color.get_blue() * 255);
            for (int i = 0; i < 12; i++) {
              it[i] = color;
            }
      - addressable_twinkle:
          name: "Twinkle"
          twinkle_probability: 50%
      - addressable_lambda:
          name: "Error"
          update_interval: 10ms
          lambda: |-
            static uint8_t brightness_step = 0;
            static bool brightness_decreasing = true;
            static uint8_t brightness_step_number = 10;
            if (initial_run) {
              brightness_step = 0;
              brightness_decreasing = true;
            }
            Color error_color(255, 0, 0);
            for (int i = 0; i < 12; i++) {
              it[i] = error_color * uint8_t(255/brightness_step_number*(brightness_step_number-brightness_step));
            }
            if (brightness_decreasing) {
              brightness_step++;
            } else {
              brightness_step--;
            }
            if (brightness_step == 0 || brightness_step == brightness_step_number) {
              brightness_decreasing = !brightness_decreasing;
            }
      - addressable_lambda:
          name: "Timer Ring"
          update_interval: 10ms
          lambda: |-
            static uint8_t brightness_step = 0;
            static bool brightness_decreasing = true;
            static uint8_t brightness_step_number = 10;
            if (initial_run) {
              brightness_step = 0;
              brightness_decreasing = true;
            }
            auto light_color = id(led_ring).current_values;
            Color color(light_color.get_red() * 255, light_color.get_green() * 255,
                  light_color.get_blue() * 255);
            Color muted_color(255, 0, 0);
            for (int i = 0; i < 12; i++) {
              it[i] = color * uint8_t(255/brightness_step_number*(brightness_step_number-brightness_step));
            }
            if ( id(master_mute_switch).state ) {
              it[3] = muted_color;
              it[9] = muted_color;
            }
            if (brightness_decreasing) {
              brightness_step++;
            } else {
              brightness_step--;
            }
            if (brightness_step == 0 || brightness_step == brightness_step_number) {
              brightness_decreasing = !brightness_decreasing;
            }
      - addressable_lambda:
          name: "Timer Tick"
          update_interval: 100ms
          lambda: |-
            auto light_color = id(led_ring).current_values;
            Color color(light_color.get_red() * 255, light_color.get_green() * 255,
                  light_color.get_blue() * 255);
            Color muted_color(255, 0, 0);
            auto timer_ratio = 12.0f * id(first_active_timer).seconds_left / max(id(first_active_timer).total_seconds , static_cast<uint32_t>(1));
            uint8_t last_led_on = static_cast<uint8_t>(ceil(timer_ratio)) - 1;
            for (int i = 0; i < 12; i++) {
              float brightness_dip = ( i == id(global_led_animation_index) % 12 && i != last_led_on ) ? 0.9f : 1.0f ;
              if (i <= timer_ratio) {
                it[i] = color * min(255.0f * brightness_dip * (timer_ratio - i) , 255.0f * brightness_dip) ;
              } else {
                it[i] = Color::BLACK;
              }
            }
            if (id(master_mute_switch).state) {
              it[2] = Color::BLACK;
              it[3] = muted_color;
              it[4] = Color::BLACK;
              it[8] = Color::BLACK;
              it[9] = muted_color;
              it[10] = Color::BLACK;
            }
            id(global_led_animation_index) = (12 + id(global_led_animation_index) - 1) % 12;
      - addressable_rainbow:
          name: "Rainbow"
          width: 12
      - addressable_lambda:
          name: "Tick"
          update_interval: 333ms
          lambda: |-
            static uint8_t index = 0;
            Color color(255, 0, 0);
            if (initial_run) {
              index = 0;
            }
            for (int i = 0; i < 12; i++) {
              if (i <= index ) {
                it[i] = Color::BLACK;
              } else {
                it[i] = color;
              }
            }
            index = (index + 1) % 12;
      - addressable_lambda:
          name: "Factory Reset Coming Up"
          update_interval: 1s
          lambda: |-
            static uint8_t index = 0;
            Color color(255, 0, 0);
            if (initial_run) {
              index = 0;
            }
            for (int i = 0; i < 12; i++) {
              if (i <= index ) {
                it[i] = color;
              } else {
                it[i] = Color::BLACK;
              }
            }
            index = (index + 1) % 12;

  # User facing LED ring. Remapping of the internal LEDs.
  # Exposed to be used by the user.
  - platform: partition
    id: led_ring
    name: LED Ring
    entity_category: config
    icon: "mdi:circle-outline"
    default_transition_length: 0ms
    restore_mode: RESTORE_DEFAULT_OFF
    initial_state:
      color_mode: rgb
      brightness: 66%
      red: 9.4%
      green: 73.3%
      blue: 94.9%
    segments:
      - id: leds_internal
        from: 7
        to: 11
      - id: leds_internal
        from: 0
        to: 6

power_supply:
  - id: led_power
    pin: GPIO45

sensor:
  # uptime string
  - platform: uptime
    name: $friendly_name Uptime
    id: uptime_sensor
    update_interval: 60s

  - platform: wifi_signal
    name: $friendly_name Signal
    update_interval: 60s

  # The dial. Used to control volume and Hue of the LED ring.
  - platform: rotary_encoder
    id: dial
    pin_a: GPIO18
    pin_b: GPIO16
    resolution: 2
    on_clockwise:
      - lambda: id(dial_touched) = true;
      - if:
          condition:
            binary_sensor.is_off: center_button
          then:
            - script.execute:
                id: control_volume
                increase_volume: true
          else:
            - script.execute:
                id: control_hue
                increase_hue: true
    on_anticlockwise:
      - lambda: id(dial_touched) = true;
      - if:
          condition:
            binary_sensor.is_off: center_button
          then:
            - script.execute:
                id: control_volume
                increase_volume: false
          else:
            - script.execute:
                id: control_hue
                increase_hue: false
    
event:
  # Event entity exposed to the user to automate on complex center button presses.
  # The simple press is not exposed as it is used to control the device itself.
  - platform: template
    id: button_press_event
    name: "Button press"
    icon: mdi:button-pointer
    device_class: button
    event_types:
      - double_press
      - triple_press
      - long_press
      - easter_egg_press

script:
  # Master script controlling the LEDs, based on different conditions : initialization in progress, wifi and api connected and voice assistant phase.
  # For the sake of simplicity and re-usability, the script calls child scripts defined below.
  # This script will be called every time one of these conditions is changing.
  - id: control_leds
    then:
      - lambda: |
          id(check_if_timers_active).execute();
          if (id(is_timer_active)){
            id(fetch_first_active_timer).execute();
          }
          if (id(improv_ble_in_progress)) {
            id(control_leds_improv_ble_state).execute();
          } else if (id(init_in_progress)) {
            id(control_leds_init_state).execute();
          } else if (!id(wifi_id).is_connected() || !id(api_id).is_connected()){
            id(control_leds_no_ha_connection_state).execute();
          } else if (id(center_button).state) {
            id(control_leds_center_button_touched).execute();
          } else if (id(dial_touched)) {
            id(control_leds_dial_touched).execute();
          } else if (id(timer_ringing).state) {
            id(control_leds_timer_ringing).execute();
          } else if (id(voice_assistant_phase) == ${voice_assist_waiting_for_command_phase_id}) {
            id(control_leds_voice_assistant_waiting_for_command_phase).execute();
          } else if (id(voice_assistant_phase) == ${voice_assist_listening_for_command_phase_id}) {
            id(control_leds_voice_assistant_listening_for_command_phase).execute();
          } else if (id(voice_assistant_phase) == ${voice_assist_thinking_phase_id}) {
            id(control_leds_voice_assistant_thinking_phase).execute();
          } else if (id(voice_assistant_phase) == ${voice_assist_replying_phase_id}) {
            id(control_leds_voice_assistant_replying_phase).execute();
          } else if (id(voice_assistant_phase) == ${voice_assist_error_phase_id}) {
            id(control_leds_voice_assistant_error_phase).execute();
          } else if (id(voice_assistant_phase) == ${voice_assist_not_ready_phase_id}) {
            id(control_leds_voice_assistant_not_ready_phase).execute();
          } else if (id(is_timer_active)) {
            id(control_leds_timer_ticking).execute();
          } else if (id(master_mute_switch).state) {
            id(control_leds_muted_or_silent).execute();
          } else if (id(external_media_player).volume == 0.0f || id(external_media_player).is_muted()) {
            id(control_leds_muted_or_silent).execute();
          } else if (id(voice_assistant_phase) == ${voice_assist_idle_phase_id}) {
            id(control_leds_voice_assistant_idle_phase).execute();
          }

  # Script executed during Improv BLE
  # Warm White Twinkle
  - id: control_leds_improv_ble_state
    then:
      - light.turn_on:
          brightness: 66%
          red: 100%
          green: 89%
          blue: 71%
          id: voice_assistant_leds
          effect: "Twinkle"

  # Script executed during initialization
  # Blue Twinkle if Wifi is connected, Else solid warm white
  - id: control_leds_init_state
    then:
      - if:
          condition:
            wifi.connected:
          then:
            - light.turn_on:
                brightness: 66%
                red: 9.4%
                green: 73.3%
                blue: 94.9%
                id: voice_assistant_leds
                effect: "Twinkle"
          else:
            - light.turn_on:
                brightness: 66%
                red: 100%
                green: 89%
                blue: 71%
                id: voice_assistant_leds
                effect: "none"

  # Script executed when the device has no connection to Home Assistant
  # Red Twinkle (This will be visible during HA updates for example)
  - id: control_leds_no_ha_connection_state
    then:
      - light.turn_on:
          brightness: 66%
          red: 1
          green: 0
          blue: 0
          id: voice_assistant_leds
          effect: "Twinkle"

  # Script executed when the voice assistant is idle (waiting for a wake word)
  # Nothing (Either LED ring off or LED ring on if the user decided to turn the user facing LED ring on)
  - id: control_leds_voice_assistant_idle_phase
    then:
      - light.turn_off: voice_assistant_leds
      - if:
          condition:
            light.is_on: led_ring
          then:
            light.turn_on: led_ring

  # Script executed when the voice assistant is waiting for a command (After the wake word)
  # Slow clockwise spin of the LED ring.
  - id: control_leds_voice_assistant_waiting_for_command_phase
    then:
      - light.turn_on:
          brightness: !lambda return max( id(led_ring).current_values.get_brightness() , 0.2f );
          id: voice_assistant_leds
          effect: "Waiting for Command"

  # Script executed when the voice assistant is listening to a command
  # Fast clockwise spin of the LED ring.
  - id: control_leds_voice_assistant_listening_for_command_phase
    then:
      - light.turn_on:
          brightness: !lambda return max( id(led_ring).current_values.get_brightness() , 0.2f );
          id: voice_assistant_leds
          effect: "Listening For Command"

  # Script executed when the voice assistant is thinking to a command
  # The spin stops and the 2 LEDs that are currently on and blinking indicating the commend is being processed.
  - id: control_leds_voice_assistant_thinking_phase
    then:
      - light.turn_on:
          brightness: !lambda return max( id(led_ring).current_values.get_brightness() , 0.2f );
          id: voice_assistant_leds
          effect: "Thinking"

  # Script executed when the voice assistant is thinking to a command
  # Fast anticlockwise spin of the LED ring.
  - id: control_leds_voice_assistant_replying_phase
    then:
      - light.turn_on:
          brightness: !lambda return max( id(led_ring).current_values.get_brightness() , 0.2f );
          id: voice_assistant_leds
          effect: "Replying"

  # Script executed when the voice assistant is in error
  # Fast Red Pulse
  - id: control_leds_voice_assistant_error_phase
    then:
      - light.turn_on:
          brightness: !lambda return min ( max( id(led_ring).current_values.get_brightness() , 0.2f ) + 0.1f , 1.0f );
          red: 1
          green: 0
          blue: 0
          id: voice_assistant_leds
          effect: "Error"

  # Script executed when the voice assistant is muted or silent
  # The LED next to the 2 microphones turn red / one red LED next to the speaker grill
  - id: control_leds_muted_or_silent
    then:
      - light.turn_on:
          brightness: !lambda return max( id(led_ring).current_values.get_brightness() , 0.2f );
          id: voice_assistant_leds
          effect: "Muted or Silent"

  # Script executed when the voice assistant is not ready
  - id: control_leds_voice_assistant_not_ready_phase
    then:
      - light.turn_on:
          brightness: 66%
          red: 1
          green: 0
          blue: 0
          id: voice_assistant_leds
          effect: "Twinkle"

  # Script executed when the dial is touched
  # A number of LEDs turn on indicating a visual representation of the volume of the media player entity.
  - id: control_leds_dial_touched
    then:
      - light.turn_on:
          brightness: !lambda return max( id(led_ring).current_values.get_brightness() , 0.2f );
          id: voice_assistant_leds
          effect: "Volume Display"

  # Script executed when the center button is touched
  # The complete LED ring turns on
  - id: control_leds_center_button_touched
    then:
      - light.turn_on:
          brightness: !lambda return min ( max( id(led_ring).current_values.get_brightness() , 0.2f ) + 0.1f , 1.0f );
          id: voice_assistant_leds
          effect: "Center Button Touched"

  # Script executed when the timer is ringing, to control the LEDs
  # The LED ring blinks.
  - id: control_leds_timer_ringing
    then:
      - light.turn_on:
          brightness: !lambda return min ( max( id(led_ring).current_values.get_brightness() , 0.2f ) + 0.1f , 1.0f );
          id: voice_assistant_leds
          effect: "Timer Ring"

  # Script executed when the timer is ticking, to control the LEDs
  # The LEDs shows the remaining time as a fraction of the full ring.
  - id: control_leds_timer_ticking
    then:
      - light.turn_on:
          brightness: !lambda return max( id(led_ring).current_values.get_brightness() , 0.2f );
          id: voice_assistant_leds
          effect: "Timer tick"

  # Script executed when the volume is increased/decreased from the dial
  - id: control_volume
    mode: restart
    parameters:
      increase_volume: bool  # True: Increase volume / False: Decrease volume.
    then:
      - delay: 16ms
      - if:
          condition:
            lambda: return increase_volume;
          then:
            - media_player.volume_up:
          else:
            - media_player.volume_down:
      - script.execute: control_leds
      - delay: 1s
      - lambda: id(dial_touched) = false;
      - sensor.rotary_encoder.set_value:
          id: dial
          value: 0
      - script.execute: control_leds

  # Script executed when the hue is increased/decreased from the dial
  - id: control_hue
    mode: restart
    parameters:
      increase_hue: bool  # True: Increase hue / False: Decrease hue.
    then:
      - delay: 16ms
      - if:
          condition:
            lambda: return(abs(int(id(dial).state)) > 3 || id(color_changed));
          then:
            - lambda: |
                id(color_changed) = true;
                auto light_color = id(voice_assistant_leds).current_values;
                int hue = 0;
                float saturation = 0;
                float value = 0;
                rgb_to_hsv( light_color.get_red(),
                            light_color.get_green(),
                            light_color.get_blue(),
                            hue,
                            saturation,
                            value);
                if (increase_hue) {
                  hue = (hue + 10) % 360;
                } else {
                  hue = (hue + 350) % 360;
                }
                if (saturation < 0.05) {
                  saturation = 1;
                }
                float red = 0;
                float green = 0;
                float blue = 0;
                hsv_to_rgb( hue,
                            saturation,
                            value,
                            red,
                            green,
                            blue);
                id(voice_assistant_leds).make_call().set_rgb(red, green, blue).perform();
      - wait_until:
          binary_sensor.is_off: center_button
      - lambda: |
          id(dial_touched) = false;
          // now we "save" the new LED color/state to led_ring, maintaining its brightness and state
          auto led_ring_call = id(led_ring).make_call();
          auto va_leds_cv = id(voice_assistant_leds).current_values;
          led_ring_call.from_light_color_values(va_leds_cv);
          led_ring_call.set_brightness(id(led_ring).current_values.get_brightness());
          led_ring_call.set_state(id(led_ring).current_values.is_on());
          led_ring_call.perform();
      - sensor.rotary_encoder.set_value:
          id: dial
          value: 0
      - script.execute: control_leds
      - delay: 500ms
      - lambda: id(color_changed) = false;

  # Script executed when the timer is ringing, to playback sounds.
  - id: ring_timer
    then:
      - script.execute: enable_repeat_one
      - script.execute:
          id: play_sound
          priority: true
          sound_file: !lambda return id(timer_finished_sound);

  # Script executed when the timer is ringing, to repeat the timer finished sound.
  - id: enable_repeat_one
    then:
      # Turn on the repeat mode and pause for 500 ms between playlist items/repeats
      - lambda: |-
            id(external_media_player)
              ->make_call()
              .set_command(media_player::MediaPlayerCommand::MEDIA_PLAYER_COMMAND_REPEAT_ONE)
              .set_announcement(true)
              .perform();
            id(external_media_player)->set_playlist_delay_ms(speaker::AudioPipelineType::ANNOUNCEMENT, 500);

  # Script execute when the timer is done ringing, to disable repeat mode.
  - id: disable_repeat
    then:
      # Turn off the repeat mode and pause for 0 ms between playlist items/repeats
      - lambda: |-
            id(external_media_player)
              ->make_call()
              .set_command(media_player::MediaPlayerCommand::MEDIA_PLAYER_COMMAND_REPEAT_OFF)
              .set_announcement(true)
              .perform();
            id(external_media_player)->set_playlist_delay_ms(speaker::AudioPipelineType::ANNOUNCEMENT, 0);

  # Script executed when we want to play sounds on the device.
  - id: play_sound
    parameters:
      priority: bool
      sound_file: "audio::AudioFile*"
    then:
      - lambda: |-
          if (priority) {
            id(external_media_player)
              ->make_call()
              .set_command(media_player::MediaPlayerCommand::MEDIA_PLAYER_COMMAND_STOP)
              .set_announcement(true)
              .perform();
          }
          if ( (id(external_media_player).state != media_player::MediaPlayerState::MEDIA_PLAYER_STATE_ANNOUNCING ) || priority) {
            id(external_media_player)
              ->play_file(sound_file, true, false);
          }

  # Script used to fetch the first active timer (Stored in global first_active_timer)
  - id: fetch_first_active_timer
    then:
      - lambda: |
          const auto timers = id(va).get_timers();
          auto output_timer = timers.begin()->second;
          for (auto &iterable_timer : timers) {
            if (iterable_timer.second.is_active && iterable_timer.second.seconds_left <= output_timer.seconds_left) {
              output_timer = iterable_timer.second;
            }
          }
          id(first_active_timer) = output_timer;

  # Script used to check if a timer is active (Stored in global is_timer_active)
  - id: check_if_timers_active
    then:
      - lambda: |
          const auto timers = id(va).get_timers();
          bool output = false;
          if (timers.size() > 0) {
            for (auto &iterable_timer : timers) {
              if(iterable_timer.second.is_active) {
                output = true;
              }
            }
          }
          id(is_timer_active) = output;

  # Script used activate the stop word if the TTS step is long.
  # Why is this wrapped on a script?
  #   Becasue we want to stop the sequence if the TTS step is faster than that.
  #   This allows us to prevent having the deactivation of the stop word before its own activation.
  - id: activate_stop_word_once
    then:
      - delay: 1s
      # Enable stop wake word
      - if:
          condition:
            switch.is_off: timer_ringing
          then:
            - micro_wake_word.enable_model: stop
            - wait_until:
                not:
                  media_player.is_announcing:
            - if:
                condition:
                  switch.is_off: timer_ringing
                then:
                  - micro_wake_word.disable_model: stop

# Audio and Voice Assistant Config
i2s_audio:
  - id:  i2s_input               # For microphone
    i2s_lrclk_pin: GPIO9         # WS Pin of the INMP441 Omni Mic
    i2s_bclk_pin: GPIO10         # SCK Pin of the INMP441 Omni Mic

  - id: i2s_output               # For Speaker
    i2s_lrclk_pin: GPIO7         # LRC Pin of the MAX98357A Audio Amp
    i2s_bclk_pin: GPIO6          # BLCK Pin of the MAX98357A Audio Amp

microphone:
  - platform: i2s_audio
    id: i2s_mics
    i2s_din_pin: GPIO8           # SD Pin of the INMP441 MEMS Microphone
    adc_type: external
    pdm: false
    sample_rate: 16000
    bits_per_sample: 32bit
    i2s_audio_id: i2s_input
    channel: stereo
    
speaker:
  # Hardware speaker output
  - platform: i2s_audio
    id: i2s_audio_speaker
    sample_rate: 48000
    i2s_dout_pin: GPIO4         # DIN Pin of the MAX98357A DAC Audio Amplifier
    bits_per_sample: 32bit
    i2s_audio_id: i2s_output
    dac_type: external
    channel: stereo
    timeout: never
    buffer_duration: 100ms

  # Virtual speakers to combine the announcement and media streams together into one output
  - platform: mixer
    id: mixing_speaker
    output_speaker: i2s_audio_speaker
    num_channels: 2
    source_speakers:
      - id: announcement_mixing_input
        timeout: never
      - id: media_mixing_input
        timeout: never

  # Virtual speakers to resample each pipelines' audio, if necessary, as the mixer speaker requires the same sample rate
  - platform: resampler
    id: announcement_resampling_speaker
    output_speaker: announcement_mixing_input
    sample_rate: 48000
    bits_per_sample: 16
  - platform: resampler
    id: media_resampling_speaker
    output_speaker: media_mixing_input
    sample_rate: 48000
    bits_per_sample: 16
    
media_player:
  - platform: speaker
    id: external_media_player
    name: Media Player
    internal: False
    volume_increment: 0.05
    volume_min: 0.4
    volume_max: 0.85
    announcement_pipeline:
      speaker: announcement_resampling_speaker
      format: FLAC     # FLAC is the least processor intensive codec
      num_channels: 1  # Stereo audio is unnecessary for announcements
      sample_rate: 48000
    media_pipeline:
      speaker: media_resampling_speaker
      format: FLAC     # FLAC is the least processor intensive codec
      num_channels: 2
      sample_rate: 48000
    on_mute:
      - script.execute: control_leds
    on_unmute:
      - script.execute: control_leds
    on_volume:
      - script.execute: control_leds
    on_announcement:
      - mixer_speaker.apply_ducking:
          id: media_mixing_input
          decibel_reduction: 20
          duration: 0.0s
    on_state:
      if:
        condition:
          and:
            - switch.is_off: timer_ringing
            - not:
                voice_assistant.is_running:
            - not:
                media_player.is_announcing:
        then:
          - mixer_speaker.apply_ducking:
              id: media_mixing_input
              decibel_reduction: 0
              duration: 1.0s

    files:
      - id: center_button_press_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/center_button_press.flac
      - id: center_button_double_press_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/center_button_double_press.flac
      - id: center_button_triple_press_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/center_button_triple_press.flac
      - id: center_button_long_press_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/center_button_long_press.flac
      - id: factory_reset_initiated_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/factory_reset_initiated.mp3
      - id: factory_reset_cancelled_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/factory_reset_cancelled.mp3
      - id: factory_reset_confirmed_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/factory_reset_confirmed.mp3
      - id: jack_connected_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/jack_connected.flac
      - id: jack_disconnected_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/jack_disconnected.flac
      - id: mute_switch_on_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/mute_switch_on.flac
      - id: mute_switch_off_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/mute_switch_off.flac
      - id: timer_finished_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/timer_finished.flac
      - id: wake_word_triggered_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/wake_word_triggered.flac
      - id: easter_egg_tick_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/easter_egg_tick.mp3
      - id: easter_egg_tada_sound
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/easter_egg_tada.mp3
      - id: error_cloud_expired
        file: https://github.com/esphome/home-assistant-voice-pe/raw/dev/sounds/error_cloud_expired.mp3

micro_wake_word:
  id: mww
  microphone:
    microphone: i2s_mics
    channels: 1
    gain_factor: 4
  stop_after_detection: false
  models:
    - model: https://github.com/kahrendt/microWakeWord/releases/download/okay_nabu_20241226.3/okay_nabu.json
      id: okay_nabu
    - model: hey_jarvis
      id: hey_jarvis
    - model: hey_mycroft
      id: hey_mycroft
    - model: https://github.com/kahrendt/microWakeWord/releases/download/stop/stop.json
      id: stop
      internal: true
  vad:
  on_wake_word_detected:
    # If the wake word is detected when the device is muted (Possible with the software mute switch): Do nothing
    - if:
        condition:
          switch.is_off: master_mute_switch
        then:
          # If a timer is ringing: Stop it, do not start the voice assistant (We can stop timer from voice!)
          - if:
              condition:
                switch.is_on: timer_ringing
              then:
                - switch.turn_off: timer_ringing
              # Stop voice assistant if running
              else:
                - if:
                    condition:
                      voice_assistant.is_running:
                    then:
                      voice_assistant.stop:
                    # Stop any other media player announcement
                    else:
                      - if:
                          condition:
                            media_player.is_announcing:
                          then:
                            - media_player.stop:
                                announcement: true
                          # Start the voice assistant and play the wake sound, if enabled
                          else:
                            - if:
                                condition:
                                  switch.is_on: wake_sound
                                then:
                                  - script.execute:
                                      id: play_sound
                                      priority: true
                                      sound_file: !lambda return id(wake_word_triggered_sound);
                                  - delay: 300ms
                            - voice_assistant.start:
                                wake_word: !lambda return wake_word;

voice_assistant:
  id: va
  microphone:
    microphone: i2s_mics
    channels: 0
    gain_factor: 16
  media_player: external_media_player
  micro_wake_word: mww
  use_wake_word: false
  noise_suppression_level: 1
  auto_gain: 31dbfs
  volume_multiplier: 4.0
  on_client_connected:
    - lambda: id(init_in_progress) = false;
    - micro_wake_word.start:
    - lambda: id(voice_assistant_phase) = ${voice_assist_idle_phase_id};
    - script.execute: control_leds
  on_client_disconnected:
    - voice_assistant.stop:
    - lambda: id(voice_assistant_phase) = ${voice_assist_not_ready_phase_id};
    - script.execute: control_leds
  on_error:
    # Only set the error phase if the error code is different than duplicate_wake_up_detected or stt-no-text-recognized
    # These two are ignored for a better user experience
    - if:
        condition:
          and:
            - lambda: return !id(init_in_progress);
            - lambda: return code != "duplicate_wake_up_detected";
            - lambda: return code != "stt-no-text-recognized";
        then:
          - lambda: id(voice_assistant_phase) = ${voice_assist_error_phase_id};
          - script.execute: control_leds
    # If the error code is cloud-auth-failed, serve a local audio file guiding the user.
    - if:
        condition:
          - lambda: return code == "cloud-auth-failed";
        then:
          - script.execute:
              id: play_sound
              priority: true
              sound_file: !lambda return id(error_cloud_expired);
  # When the voice assistant starts: Play a wake up sound, duck audio.
  on_start:
    - mixer_speaker.apply_ducking:
        id: media_mixing_input
        decibel_reduction: 20  # Number of dB quieter; higher implies more quiet, 0 implies full volume
        duration: 0.0s         # The duration of the transition (default is no transition)
  on_listening:
    - lambda: id(voice_assistant_phase) = ${voice_assist_waiting_for_command_phase_id};
    - script.execute: control_leds
  on_stt_vad_start:
    - lambda: id(voice_assistant_phase) = ${voice_assist_listening_for_command_phase_id};
    - script.execute: control_leds
  on_stt_vad_end:
    - lambda: id(voice_assistant_phase) = ${voice_assist_thinking_phase_id};
    - script.execute: control_leds
  on_tts_start:
    - lambda: id(voice_assistant_phase) = ${voice_assist_replying_phase_id};
    - script.execute: control_leds
    # Start a script that would potentially enable the stop word if the response is longer than a second
    - script.execute: activate_stop_word_once
  # When the voice assistant ends ...
  on_end:
    - wait_until:
        not:
          voice_assistant.is_running:
    # Stop ducking audio.
    - mixer_speaker.apply_ducking:
        id: media_mixing_input
        decibel_reduction: 0
        duration: 1.0s
    # If the end happened because of an error, let the error phase on for a second
    - if:
        condition:
          lambda: return id(voice_assistant_phase) == ${voice_assist_error_phase_id};
        then:
          - delay: 1s
    # Reset the voice assistant phase id and reset the LED animations.
    - lambda: id(voice_assistant_phase) = ${voice_assist_idle_phase_id};
    - script.execute: control_leds
  on_timer_finished:
    - switch.turn_on: timer_ringing
  on_timer_started:
    - script.execute: control_leds
  on_timer_cancelled:
    - script.execute: control_leds
  on_timer_updated:
    - script.execute: control_leds
  on_timer_tick:
    - script.execute: control_leds

button:
  - platform: factory_reset
    id: factory_reset_button
    name: "Factory Reset"
    entity_category: diagnostic
    internal: true
  - platform: restart
    id: restart_button
    name: "Restart"
    entity_category: config
    disabled_by_default: true
    icon: "mdi:restart"

debug:
  update_interval: 5s