Skip to content

Instantly share code, notes, and snippets.

@GPSBabelDeveloper

GPSBabelDeveloper/gist:61ef919c0dbf0fd3d349dce2d1ab4d28

Created November 29, 2021 10:13
Show Gist options
  • Save GPSBabelDeveloper/61ef919c0dbf0fd3d349dce2d1ab4d28 to your computer and use it in GitHub Desktop.
Save GPSBabelDeveloper/61ef919c0dbf0fd3d349dce2d1ab4d28 to your computer and use it in GitHub Desktop.
Download ZIP
Unhappy Nezha boot
Raw
gistfile1.txt
% sudo cu -s115200 -l /dev/cu.usbserial-A50285BI
Connected.
�3[188]HELLO! BOOT0 is starting!
[191]BOOT0 commit : 2337244-dirty
OpenSBI v0.6
____ _____ ____ _____
/ __ \ / ____| _ \_ _|
| | | |_ __ ___ _ __ | (___ | |_) || |
| | | | '_ \ / _ \ '_ \ \___ \| _ < | |
| |__| | |_) | __/ | | |____) | |_) || |_
\____/| .__/ \___|_| |_|_____/|____/_____|
| |
|_|
Platform Name : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs : 1
Current Hart : 0
Firmware Base : 0x40000400
Firmware Size : 75 KB
Runtime SBI Version : 0.2
MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0 : 0x0000000040000000-0x000000004001ffff (A)
PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,�
U-Boot 2018.05-00107-gc22c3d075c (Apr 24 2021 - 07:52:58 +0000) Allwinner Technology
[00.428]DRAM: 2 GiB
[00.430]Relocation Offset is: 7deeb000
[00.434]secure enable bit: 0
[00.437]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
initr_ledc
unable to find ledc node in device tree.
[00.448]flash init start
[00.450]workmode = 0,storage type = 0
[00.456]sunxi-spinand-phy: not detect any munufacture from id table
[00.463]sunxi-spinand-phy: get spi-nand Model from fdt fail
[00.468]sunxi-spinand-phy: get phy info from fdt fail
device nand0 <nand>, # parts = 4
#: name size offset mask_flags
0: boot0 0x00100000 0x00000000 1
1: uboot 0x00300000 0x00100000 1
2: secure_storage 0x00100000 0x00400000 1
3: sys 0x0fb00000 0x00500000 0
active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000
defaults:
mtdids : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[00.806]ubi0: attaching mtd4
[01.202]ubi0: scanning is finished
[01.212]ubi0: attached mtd4 (name "sys", size 251 MiB)
[01.217]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[01.223]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[01.229]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[01.236]ubi0: good PEBs: 1004, bad PEBs: 0, corrupted PEBs: 0
[01.241]ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[01.248]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[01.255]ubi0: available PEBs: 0, total reserved PEBs: 1004, PEBs reserved for bad PEB handling: 40
[01.264]sunxi flash init ok
[01.267]line:714 init_clocks
__clk_init: clk pll_periph0x2 already initialized
register fix_factor clk error
[01.277]drv_disp_init
partno erro : can't find partition bootloader
** Unable to read file lcd_compatible_index.txt **
[01.514]do_fat_fsload for lcd config failed
request pwm success, pwm2:pwm2:0x2000c00.
[01.528]drv_disp_init finish
[01.531]boot_gui_init:start
[01.534]set disp.dev2_output_type fail. using defval=0
[01.725]boot_gui_init:finish
[02.138]LCD open finish
partno erro : can't find partition bootloader
54 bytes read in 0 ms
[02.299]bmp_name=bootlogo.bmp size 38454
38454 bytes read in 4 ms (9.2 MiB/s)
[02.515]Loading Environment from SUNXI_FLASH... OK
[02.548]Item0 (Map) magic is bad
[02.551]usb burn from boot
delay time 0
weak:otg_phy_config
[02.562]usb prepare ok
[03.365]overtime
[03.369]do_burn_from_boot usb : no usb exist
[03.393]update bootcmd
[03.415]change working_fdt 0xbeaaad70 to 0xbea8ad70
partno erro : can't find partition bootloader
** Unable to read file lcd_compatible_index.txt **
[03.466]do_fat_fsload for lcd config failed
partno erro : can't find partition bootloader
[03.494]please enable FAT_WRITE for lcd compatible first
partno erro : can't find partition bootloader
** Unable to read file lcd_compatible_index.txt **
[03.528]do_fat_fsload for lcd config failed
[03.532]libfdt fdt_path_offset() for lcd
[03.536]update dts
Hit any key to stop autoboot: 0
dsp0:gpio init config fail
DSP0 start ok, img length 252960, booting from 0x400660
Android's image name: d1-nezha
No reserved memory region found in source FDT
[04.492]
Starting kernel ...
[ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000
[ 0.000000] Linux version 5.4.61 (wuhuabin@AwExdroid86) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #51 PREEMPT Mon May 10 12:41:05 UTC 2021
[ 0.000000] cma: Reserved 8 MiB at 0x00000000bf800000
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000bfffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040200000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x00000000bfffffff]
[ 0.000000] On node 0 totalpages: 523776
[ 0.000000] DMA32 zone: 7161 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 523776 pages, LIFO batch:63
[ 0.000000] elf_hwcap is 0x20112d
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516615
[ 0.000000] Kernel command line: ubi.mtd=sys ubi.block=0,rootfs earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/ubiblock0_5 rootfstype=squashfs init=/sbin/init partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@ubi0_2:env-redund@ubi0_3:boot@ubi0_4:rootfs@ubi0_5:dsp0@ubi0_6:recovery@ubi0_7:UDISK@ubi0_8: cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun20iw1p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message=2018.05-00107-gc22c3d075c(04/24/20
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Sorting __ex_table...
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2040724K/2095104K available (5944K kernel code, 655K rwdata, 2062K rodata, 208K init, 251K bss, 46188K reserved, 8192K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts.
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000005] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000023] riscv_timer_clockevent depends on broadcast, but no broadcast function available
[ 0.000330] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000925] Console: colour dummy device 80x25
[ 0.000965] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000980] pid_max: default: 32768 minimum: 301
[ 0.001190] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.001227] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.002954] ASID allocator initialised with 65536 entries
[ 0.003117] rcu: Hierarchical SRCU implementation.
[ 0.003914] devtmpfs: initialized
[ 0.015827] random: get_random_u32 called from bucket_table_alloc.isra.31+0x4e/0x15e with crng_init=0
[ 0.016703] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.016732] futex hash table entries: 256 (order: 0, 6144 bytes, linear)
[ 0.017162] pinctrl core: initialized pinctrl subsystem
[ 0.018482] NET: Registered protocol family 16
[ 0.020416] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.021044] cpuidle: using governor menu
[ 0.066183] rtc_ccu: sunxi ccu init OK
[ 0.072601] clock: sunxi ccu init OK
[ 0.073536] clock: sunxi ccu init OK
[ 0.112369] iommu: Default domain type: Translated
[ 0.112541] sunxi iommu: irq = 4
[ 0.113712] SCSI subsystem initialized
[ 0.114052] usbcore: registered new interface driver usbfs
[ 0.114154] usbcore: registered new interface driver hub
[ 0.114256] usbcore: registered new device driver usb
[ 0.114436] mc: Linux media interface: v0.10
[ 0.114499] videodev: Linux video capture interface: v2.00
[ 0.115456] Advanced Linux Sound Architecture Driver Initialized.
[ 0.116050] Bluetooth: Core ver 2.22
[ 0.116129] NET: Registered protocol family 31
[ 0.116141] Bluetooth: HCI device and connection manager initialized
[ 0.116160] Bluetooth: HCI socket layer initialized
[ 0.116173] Bluetooth: L2CAP socket layer initialized
[ 0.116207] Bluetooth: SCO socket layer initialized
[ 0.116489] pwm module init!
[ 0.118032] g2d 5410000.g2d: Adding to iommu group 0
[ 0.118515] G2D: rcq version initialized.major:250
[ 0.119062] input: sunxi-keyboard as /devices/virtual/input/input0
[ 0.120666] clocksource: Switched to clocksource riscv_clocksource
[ 0.132419] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[ 0.148075] NET: Registered protocol family 2
[ 0.148851] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.148952] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.149148] TCP bind hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.149303] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.149489] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.149592] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.149915] NET: Registered protocol family 1
[ 0.151244] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[ 0.151816] spi spi0: spi0 supply spi not found, using dummy regulator
[ 0.152083] sunxi_spi_resource_get()2062 - [spi0] SPI MASTER MODE
[ 0.152192] sunxi_spi_clk_init()2138 - [spi0] mclk 100000000
[ 0.152859] sunxi_spi_probe()2542 - [spi0]: driver probe succeed, base ffffffd00405a000, irq 31
[ 0.154720] Initialise system trusted keyrings
[ 0.154970] workingset: timestamp_bits=62 max_order=19 bucket_order=0
[ 0.162572] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.183983] Key type asymmetric registered
[ 0.183998] Asymmetric key parser 'x509' registered
[ 0.184021] io scheduler mq-deadline registered
[ 0.184029] io scheduler kyber registered
[ 0.184049] atomic64_test: passed
[ 0.185244] [DISP]disp_module_init
[ 0.185811] disp 5000000.disp: Adding to iommu group 0
[ 0.186417] [DISP] disp_init,line:2385:
[ 0.186423] smooth display screen:0 type:1 mode:4
[ 0.222767] display_fb_request,fb_id:0
[ 0.252625] disp_al_manager_apply ouput_type:1
[ 0.252787] [DISP] lcd_clk_config,line:731:
[ 0.252799] disp 0, clk: pll(420000000),clk(420000000),dclk(70000000) dsi_rate(70000000)
[ 0.252799] clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000)
[ 0.253198] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[ 0.253941] [DISP]disp_module_init finish
[ 0.254866] sunxi_sid_init()497 - insmod ok
[ 0.255419] pwm-regulator: supplied by regulator-dummy
[ 0.262719] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[ 0.263162] uart uart0: get regulator failed
[ 0.263193] uart uart0: uart0 supply uart not found, using dummy regulator
[ 0.263515] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI
[ 0.263542] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n
[ 1.052134] printk: console [ttyS0] enabled
[ 1.057704] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[ 1.069166] uart uart1: get regulator failed
[ 1.073992] uart uart1: uart1 supply uart not found, using dummy regulator
[ 1.082046] uart1: ttyS1 at MMIO 0x2500400 (irq = 19, base_baud = 1500000) is a SUNXI
[ 1.091988] misc dump reg init
[ 1.096007] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[ 1.103302] sunxi-rfkill soc@3000000:rfkill@0: devm_pinctrl_get() failed!
[ 1.110912] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[ 1.118222] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[ 1.125640] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[ 1.132171] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[ 1.139102] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1)
[ 1.146831] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1
[ 1.154729] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[ 1.162854] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[ 1.170492] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[ 1.177254] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1)
[ 1.184833] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0
[ 1.193104] [ADDR_MGT] addr_mgt_probe: module version: v1.0.8
[ 1.200755] [ADDR_MGT] addr_mgt_probe: success.
[ 1.206759] sunxi-spinand: AW SPINand MTD Layer Version: 2.0 20201228
[ 1.214089] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306
[ 1.221989] sunxi-spinand-phy: not detect any munufacture from id table
[ 1.229371] sunxi-spinand-phy: get spi-nand Model from fdt fail
[ 1.236068] sunxi-spinand-phy: get phy info from fdt fail
[ 1.242117] sunxi-spinand-phy: not detect munufacture from fdt
[ 1.248815] sunxi-spinand-phy: detect munufacture from id table: Mxic
[ 1.256030] sunxi-spinand-phy: detect spinand id: ff0326c2 ffffffff
[ 1.263074] sunxi-spinand-phy: ========== arch info ==========
[ 1.269574] sunxi-spinand-phy: Model: MX35LF2GE4AD
[ 1.276291] sunxi-spinand-phy: Munufacture: Mxic
[ 1.282262] sunxi-spinand-phy: DieCntPerChip: 1
[ 1.287892] sunxi-spinand-phy: BlkCntPerDie: 2048
[ 1.293831] sunxi-spinand-phy: PageCntPerBlk: 64
[ 1.299573] sunxi-spinand-phy: SectCntPerPage: 4
[ 1.305226] sunxi-spinand-phy: OobSizePerPage: 64
[ 1.310971] sunxi-spinand-phy: BadBlockFlag: 0x1
[ 1.316810] sunxi-spinand-phy: OperationOpt: 0x7
[ 1.322658] sunxi-spinand-phy: MaxEraseTimes: 65000
[ 1.328689] sunxi-spinand-phy: EccFlag: 0x2
[ 1.334537] sunxi-spinand-phy: EccType: 8
[ 1.340163] sunxi-spinand-phy: EccProtectedType: 3
[ 1.345840] sunxi-spinand-phy: ========================================
[ 1.353235] sunxi-spinand-phy:
[ 1.356732] sunxi-spinand-phy: ========== physical info ==========
[ 1.363672] sunxi-spinand-phy: TotalSize: 256 M
[ 1.369009] sunxi-spinand-phy: SectorSize: 512 B
[ 1.374367] sunxi-spinand-phy: PageSize: 2 K
[ 1.379528] sunxi-spinand-phy: BlockSize: 128 K
[ 1.384888] sunxi-spinand-phy: OOBSize: 64 B
[ 1.390127] sunxi-spinand-phy: ========================================
[ 1.397547] sunxi-spinand-phy:
[ 1.401066] sunxi-spinand-phy: ========== logical info ==========
[ 1.407856] sunxi-spinand-phy: TotalSize: 256 M
[ 1.413244] sunxi-spinand-phy: SectorSize: 512 B
[ 1.418580] sunxi-spinand-phy: PageSize: 4 K
[ 1.423743] sunxi-spinand-phy: BlockSize: 256 K
[ 1.429095] sunxi-spinand-phy: OOBSize: 128 B
[ 1.434457] sunxi-spinand-phy: ========================================
[ 1.442001] sunxi-spinand-phy: block lock register: 0x00
[ 1.448090] sunxi-spinand-phy: feature register: 0x11
[ 1.453757] sunxi-spinand-phy: sunxi physic nand init end
[ 1.460425] Creating 4 MTD partitions on "sunxi_mtd_nand":
[ 1.466637] 0x000000000000-0x000000100000 : "boot0"
[ 1.481898] 0x000000100000-0x000000500000 : "uboot"
[ 1.488023] random: fast init done
[ 1.521824] 0x000000500000-0x000000600000 : "secure_storage"
[ 1.541851] 0x000000600000-0x000010000000 : "sys"
[ 1.931385] random: crng init done
[ 2.672355] libphy: Fixed MDIO Bus: probed
[ 2.676959] CAN device driver interface
[ 2.682836] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[ 2.694208] sunxi gmac driver's version: 1.0.0
[ 2.699306] gmac-power0: NULL
[ 2.702659] gmac-power1: NULL
[ 2.705966] gmac-power2: NULL
[ 2.710431] Failed to alloc md5
[ 2.714029] eth0: Use random mac address
[ 2.718766] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.726183] sunxi-ehci: EHCI SUNXI driver
[ 2.731298] get ehci1-controller wakeup-source is fail.
[ 2.737227] sunxi ehci1-controller don't init wakeup source
[ 2.743574] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe0008d6748, 0x:ffffffd004079000, irq_no:31
[ 2.757140] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator
[ 2.769762] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[ 2.777079] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[ 2.786903] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000
[ 2.820715] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[ 2.829453] hub 1-0:1.0: USB hub found
[ 2.833770] hub 1-0:1.0: 1 port detected
[ 2.839005] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.845999] sunxi-ohci: OHCI SUNXI driver
[ 2.851104] get ohci1-controller wakeup-source is fail.
[ 2.857069] sunxi ohci1-controller don't init wakeup source
[ 2.863328] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe0008d7288
[ 2.873802] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator
[ 2.886312] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[ 2.893632] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[ 2.903472] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400
[ 2.985680] hub 2-0:1.0: USB hub found
[ 2.989916] hub 2-0:1.0: 1 port detected
[ 2.995414] usbcore: registered new interface driver uas
[ 3.001626] usbcore: registered new interface driver usb-storage
[ 3.008400] usbcore: registered new interface driver ums-alauda
[ 3.015150] usbcore: registered new interface driver ums-cypress
[ 3.022012] usbcore: registered new interface driver ums-datafab
[ 3.028778] usbcore: registered new interface driver ums_eneub6250
[ 3.035827] usbcore: registered new interface driver ums-freecom
[ 3.042632] usbcore: registered new interface driver ums-isd200
[ 3.049288] usbcore: registered new interface driver ums-jumpshot
[ 3.056236] usbcore: registered new interface driver ums-karma
[ 3.062847] usbcore: registered new interface driver ums-onetouch
[ 3.069788] usbcore: registered new interface driver ums-realtek
[ 3.076621] usbcore: registered new interface driver ums-sddr09
[ 3.083388] usbcore: registered new interface driver ums-sddr55
[ 3.090047] usbcore: registered new interface driver ums-usbat
[ 3.097698] sunxi_gpadc_init,1968, success
[ 3.103254] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1
[ 3.115563] sunxi-rtc 7090000.rtc: registered as rtc0
[ 3.121380] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:07 UTC (7)
[ 3.130243] sunxi-rtc 7090000.rtc: sunxi rtc probed
[ 3.136158] i2c /dev entries driver
[ 3.140145] IR NEC protocol handler initialized
[ 3.145936] sunxi cedar version 1.1
[ 3.150135] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[ 3.156421] VE: install start!!!
[ 3.156421]
[ 3.161952] VE: cedar-ve the get irq is 6
[ 3.161952]
[ 3.168292] VE: ve_debug_proc_info:00000000f128f416, data:00000000420d86b0, lock:000000000f6de4d9
[ 3.168292]
[ 3.179918] VE: install end!!!
[ 3.179918]
[ 3.185862] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 3.195023] Bluetooth: HCI UART driver ver 2.3
[ 3.200012] Bluetooth: HCI UART protocol H4 registered
[ 3.205779] Bluetooth: HCI UART protocol BCSP registered
[ 3.211723] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
[ 3.219001] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1
[ 3.225424] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1
[ 3.232043] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled!
[ 3.232043]
[ 3.240712] [XR_BT_LPM] bluesleep_probe: uart_index(1)
[ 3.250427] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50)
[ 3.260394] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[ 3.266666] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[ 3.273012] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[ 3.279438] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[ 3.285869] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[ 3.292395] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[ 3.298917] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[ 3.305447] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[ 3.312441] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[ 3.317917] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
[ 3.324588] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.335774] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[ 3.355955] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.380374] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
[ 3.386087] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 3.397866] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50)
[ 3.407970] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[ 3.414222] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[ 3.420535] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[ 3.427018] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[ 3.433452] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[ 3.439974] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[ 3.446504] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[ 3.453028] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[ 3.459575] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[ 3.469045] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.480232] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[ 3.500383] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.524621] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[ 3.532296] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 3.539314] sunxi_led_probe()1715 - start
[ 3.543807] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 3.550698] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.562359] sunxi_get_str_of_property()1560 - failed to get the string of propname led_regulator!
[ 3.572447] sunxi_register_led_classdev()1448 - led_classdev start
[ 3.581058] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 3.595563] sunxi_led_probe()1820 - finish
[ 3.600819] usbcore: registered new interface driver usbhid
[ 3.607061] usbhid: USB HID core driver
[ 3.613291] usbcore: registered new interface driver snd-usb-audio
[ 3.620205] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 3.627818] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 3.635428] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 3.643024] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 3.649765] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 3.662422] sunxi-daudio 2034000.daudio: regulator missing or invalid
[ 3.670213] [AUDIOCODEC][sunxi_codec_parse_params][2208]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1
[ 3.670213]
[ 3.687476] [AUDIOCODEC][sunxi_codec_parse_params][2244]:adcdrc_cfg:0, adchpf_cfg:0, dacdrc_cfg:0, dachpf:0
[ 3.698886] [AUDIOCODEC][sunxi_internal_codec_probe][2380]:codec probe finished
[ 3.708083] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[ 3.717934] [SNDCODEC][sunxi_card_init][583]:card init finished
[ 3.725608] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[ 3.736938] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1
[ 3.749067] [SNDCODEC][sunxi_card_dev_probe][832]:register card finished
[ 3.758392] NET: Registered protocol family 10
[ 3.764984] Segment Routing with IPv6
[ 3.769244] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.776705] NET: Registered protocol family 17
[ 3.781804] can: controller area network core (rev 20170425 abi 9)
[ 3.788804] NET: Registered protocol family 29
[ 3.793833] can: raw protocol (rev 20170425)
[ 3.798619] can: broadcast manager protocol (rev 20170425 t)
[ 3.804979] can: netlink gateway (rev 20190810) max_hops=1
[ 3.811450] Bluetooth: RFCOMM TTY layer initialized
[ 3.816933] Bluetooth: RFCOMM socket layer initialized
[ 3.822785] Bluetooth: RFCOMM ver 1.11
[ 3.827973] Loading compiled-in X.509 certificates
[ 3.835788] HDMI 2.0 driver init start!
[ 3.840079] boot_hdmi=false
[ 3.843321] ERROR: pinctrl_get for HDMI2.0 DDC fail
[ 3.850352] HDMI2.0 module init end
[ 3.880104] twi twi2: twi2 supply twi not found, using dummy regulator
[ 3.895455] pcf857x 2-0038: probed
[ 3.905612] sunxi_i2c_probe()2262 - [i2c2] probe success
[ 3.921656] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present!
[ 3.932063] sunxi-audio-card 2031060.sounddmic: snd-soc-dummy-dai <-> 2031000.dmic mapping ok
[ 3.942880] debugfs: Directory '2034000.daudio' with parent 'sndhdmi' already present!
[ 3.953494] sunxi-audio-card 20340a0.sounddaudio2: snd-soc-dummy-dai <-> 2034000.daudio mapping ok
[ 3.965177] get ehci0-controller wakeup-source is fail.
[ 3.971172] sunxi ehci0-controller don't init wakeup source
[ 3.977419] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0008d6388, 0x:ffffffd0052f5000, irq_no:2e
[ 3.990947] [sunxi-ehci0]: Not init ehci0
[ 3.995919] get ohci0-controller wakeup-source is fail.
[ 4.001903] sunxi ohci0-controller don't init wakeup source
[ 4.008149] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0008d6ec8
[ 4.018576] [sunxi-ohci0]: Not init ohci0
[ 4.024317] ubi0: attaching mtd3
[ 5.005494] ubi0: scanning is finished
[ 5.025865] ubi0: attached mtd3 (name "sys", size 250 MiB)
[ 5.032089] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[ 5.039754] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[ 5.047347] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.055176] ubi0: good PEBs: 1000, bad PEBs: 0, corrupted PEBs: 0
[ 5.062037] ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[ 5.070113] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[ 5.079473] ubi0: available PEBs: 16, total reserved PEBs: 984, PEBs reserved for bad PEB handling: 20
[ 5.089921] ubi0: background thread "ubi_bgt0d" started, PID 69
[ 5.098599] block ubiblock0_5: created from ubi0:5(rootfs)
[ 5.107099] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 5.118104] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.125718] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 5.135451] clk: Not disabling unused clocks
[ 5.140218] ALSA device list:
[ 5.143657] cfg80211: failed to load regulatory.db
[ 5.149101] #0: audiocodec
[ 5.152392] #1: snddmic
[ 5.155311] #2: sndhdmi
[ 5.158237] alloc_fd: slot 0 not NULL!
[ 5.167191] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.178868] devtmpfs: mounted
[ 5.182457] Freeing unused kernel memory: 208K
[ 5.187411] This architecture does not have kernel memory protection.
[ 5.194758] Run /sbin/init as init process
[ 6.086156] init: Console is alive
[ 6.090269] init: - watchdog -
[ 6.093922] init: - preinit -
/dev/by-name/UDISK already format by ubifs
[ 7.479674] mount_root: mounting /dev/root
[ 7.484949] mount_root: loading kmods from internal overlay
[ 7.650737] hdmi_hpd_sys_config_release
[ 7.757173] block: attempting to load /etc/config/fstab
[ 7.802567] UBIFS (ubi0:8): Mounting in unauthenticated mode
[ 7.809362] UBIFS (ubi0:8): background thread "ubifs_bgt0_8" started, PID 111
[ 7.942163] UBIFS (ubi0:8): recovery needed
[ 8.280436] UBIFS (ubi0:8): recovery completed
[ 8.286200] UBIFS (ubi0:8): UBIFS: mounted UBI device 0, volume 8, name "UDISK"
[ 8.294425] UBIFS (ubi0:8): LEB size: 258048 bytes (252 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 8.305561] UBIFS (ubi0:8): FS size: 192503808 bytes (183 MiB, 746 LEBs), journal size 9420800 bytes (8 MiB, 37 LEBs)
[ 8.317466] UBIFS (ubi0:8): reserved for root: 0 bytes (0 KiB)
[ 8.324212] UBIFS (ubi0:8): media format: w4/r0 (latest is w5/r0), UUID 93F7EEFB-EA62-4260-9CEA-EA01EDF39FD0, small LPT model
[ 8.341194] block: extroot: UUID match (root: 481adc95-1d4eae8d-5ec75459-62fd1a12, overlay: 481adc95-1d4eae8d-5ec75459-62fd1a12)
[ 8.363078] mount_root: switched to extroot
[ 8.384700] procd: - early -
[ 8.388063] procd: - watchdog -
[ 8.783447] procd: - watchdog -
[ 8.787295] procd: - ubus -
[ 8.801215] procd (1): /proc/124/oom_adj is deprecated, please use /proc/124/oom_score_adj instead.
[ 9.037988] procd: - init -
Please press Enter to activate this console.
[ 9.937670] fuse: init (API version 7.31)
[ 10.318191] get ctp_power is fail, -22
[ 10.340914] get ctp_power_ldo_vol is fail, -22
[ 10.345916] sunxi_ctp_startup: ctp_power_io is invalid.
[ 10.378005] get ctp_gesture_wakeup fail, no gesture wakeup
[ 10.418798] gt9xxnew_ts 2-0014: 2-0014 supply ctp not found, using dummy regulator
[ 10.524411] file system registered
[ 10.593969] configfs-gadget 4100000.udc-controller: failed to start g1: -19
[ 10.771007] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 10.792960] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 10.851022] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 10.880917] read descriptors
[ 10.884144] read strings
[ 10.895347] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 10.930973] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 10.940295] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[ 11.140768] <<-GTP-ERROR->> GTP i2c test failed time 1.
[ 11.170921] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.190800] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.206449] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.230078] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.250995] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.260339] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[ 11.440766] <<-GTP-ERROR->> GTP i2c test failed time 2.
[ 11.470925] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.490764] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.507431] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.531473] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.551002] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.560319] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[ 11.740766] <<-GTP-ERROR->> GTP i2c test failed time 3.
[ 11.770923] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.790765] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.807430] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.830828] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.850826] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 11.860179] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[ 12.040766] <<-GTP-ERROR->> GTP i2c test failed time 4.
[ 12.070919] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 12.090644] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 12.103942] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 12.122110] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 12.132665] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14)
[ 12.143047] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[ 12.310738] <<-GTP-ERROR->> GTP i2c test failed time 5.
[ 12.341023] I2C communication ERROR!
[ 12.341061] regulator-dummy: Underflow of regulator enable count
[ 12.361220] gt9xxnew_ts: probe of 2-0014 failed with error -1
[ 14.067603] ======== XRADIO WIFI OPEN ========
[ 14.073207] [XRADIO] Driver Label:XR_V02.16.84_P2P_HT40_01.31
[ 14.079993] [XRADIO] Allocated hw_priv @ 0000000084a10f0c
[ 14.090789] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[ 14.116809] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[ 14.324283] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 14.335386] [XRADIO] Detect SDIO card 1
[ 14.350056] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[ 14.370291] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 14.395211] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 14.409869] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 14.432572] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 14.444197] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 14.456114] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[ 14.468984] mmc1: new high speed SDIO card at address 0001
[ 14.476035] [SBUS] XRadio Device:sdio clk=50000000
[ 14.490836] [XRADIO] XRADIO_HW_REV 1.0 detected.
[ 14.601311] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000.
[ 14.644255] [XRADIO] Bootloader complete
[ 14.755662] [XRADIO] Firmware completed.
[ 22.398358] [WSM] Firmware Label:XR_C09.08.52.64_DBG_02.100 2GHZ HT40 Jan 3 2020 13:14:37
[ 22.415828] [XRADIO] Firmware Startup Done.
[ 22.421003] [XRADIO_WRN] enable Multi-Rx!
[ 22.433344] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 22.478055] Error: Driver 'gt9xxnew_ts' is already registered, aborting...
[ 22.920553] ieee80211_do_open: vif_type=2, p2p=0, ch=3, addr=6c:b3:5e:87:70:86
[ 22.937646] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0, addr=6c:b3:5e:87:70:86
[ 22.959225] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined.
Trying to connect to SWUpdate...
[ 35.680734] usb1-vbus: disabling
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment