boot-3.txt

[   32.485355] can-3v3: disabling
8

U-Boot 2020.04-5.4.70-2.3.0+gad2475c056 (Nov 23 2021 - 20:58:33 +0000)

CPU:   i.MX6ULZ rev1.1 900 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 47C
Reset cause: POR
Model: i.MX6 ULZ 14x14 EVK Board
Board: Blink Sync Module
DRAM:  128 MiB
MMC:   
In:    serial
Out:   serial
Err:   serial
Waiting for button press  0sec
Waiting for button press  1sec
Waiting for button press  2sec
Waiting for button press  3sec
Waiting for button press  4sec
Normal Boot
SF: Detected w25q256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB
device 0 offset 0xea0000, size 0x10000
SF: 65536 bytes @ 0xea0000 Read: OK
device 0 offset 0x80000, size 0x500000
SF: 5242880 bytes @ 0x80000 Read: OK
device 0 offset 0x580000, size 0x900000
SF: 9437184 bytes @ 0x580000 Read: OK

Authenticate image from DDR location 0x82000000...

Secure boot enabled

HAB Configuration: 0xcc, HAB State: 0x99
No HAB Events Found!

## Loading kernel from FIT Image at 82000000 ...
   Using '[email protected]' configuration
   Trying 'kernel@1' kernel subimage
     Description:  Linux kernel
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x820000f0
     Data Size:    4417360 Bytes = 4.2 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x80800000
     Entry Point:  0x80800000
     Hash algo:    sha256
     Hash value:   a4a18d91e89fc38e8cfd1b4a83dda6360809a1dc0011f72f013a0ca24e63bd6a
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 82000000 ...
   Using '[email protected]' configuration
   Trying '[email protected]' fdt subimage
     Description:  Flattened Device Tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x82436954
     Data Size:    30349 Bytes = 29.6 KiB
     Architecture: ARM
     Hash algo:    sha256
     Hash value:   4ec5fbb3d3d113135ce0d0aa2f4fc8e6cdd274c3f2a71bfd7f70d98779005c14
   Verifying Hash Integrity ... sha256+ OK
   Booting using the fdt blob at 0x82436954
   Loading Kernel Image
   Using Device Tree in place at 82436954, end 82440fe0
Modify /soc/aips-bus@2200000/epdc@228c000:status disabled
Modify /soc/aips-bus@2100000/pxp@21cc000:status disabled
Modify /soc/aips-bus@2100000/csi@21c4000:status disabled
ft_system_setup for mx6

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.70-2.3.0+g4f2631b022d8 (oe-user@oe-host) (gcc version 9.2.0 (GCC)) #1 SMP PREEMPT Tue Nov 23 20:58:58 UTC 2021
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Freescale i.MX6 ULZ 14x14 EVK Board (Billy)
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] OF: reserved mem: failed to allocate memory for node 'linux,cma'
[    0.000000] cma: Reserved 32 MiB at 0x86000000
[    0.000000] percpu: Embedded 15 pages/cpu s31820 r8192 d21428 u61440
[    0.000000] Built 1 zonelists, mobility grouping off.  Total pages: 32480
[    0.000000] Kernel command line: console=ttymxc0,115200 ro root=/dev/mtdblock3 panic=-1 init=/init
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 81576K/131072K available (9216K kernel code, 454K rwdata, 2876K rodata, 1024K init, 412K bss, 16728K reserved, 32768K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x2c8/0x488 with crng_init=0
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000055] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.002529] Console: colour dummy device 80x30
[    0.002600] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.002638] pid_max: default: 32768 minimum: 301
[    0.003032] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.003067] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.004825] CPU: Testing write buffer coherency: ok
[    0.005580] CPU0: update cpu_capacity 1024
[    0.005611] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.007021] Setting up static identity map for 0x80100000 - 0x80100060
[    0.007349] rcu: Hierarchical SRCU implementation.
[    0.008083] smp: Bringing up secondary CPUs ...
[    0.008117] smp: Brought up 1 node, 1 CPU
[    0.008138] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[    0.008155] CPU: All CPU(s) started in SVC mode.
[    0.009053] devtmpfs: initialized
[    0.022455] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.023441] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.023496] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.026321] pinctrl core: initialized pinctrl subsystem
[    0.028827] NET: Registered protocol family 16
[    0.046328] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.049274] cpuidle: using governor menu
[    0.064237] vdd3p0: supplied by regulator-dummy
[    0.065574] cpu: supplied by regulator-dummy
[    0.066903] vddsoc: supplied by regulator-dummy
[    0.087566] No ATAGs?
[    0.087703] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.087741] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.091662] imx6ul-pinctrl 20e0000.iomuxc: Invalid fsl,pins or pins property in node /soc/aips-bus@2000000/iomuxc@20e0000/usbotg1grp
[    0.091805] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[    0.093054] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/aips-bus@2200000/iomuxc-snvs@2290000
[    0.093092] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[    0.095576] imx mu driver is registered.
[    0.096453] imx rpmsg driver is registered.
[    0.164766] SCSI subsystem initialized
[    0.165429] usbcore: registered new interface driver usbfs
[    0.165571] usbcore: registered new interface driver hub
[    0.165808] usbcore: registered new device driver usb
[    0.168940] i2c i2c-0: IMX I2C adapter registered
[    0.169875] pps_core: LinuxPPS API ver. 1 registered
[    0.169904] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.169962] PTP clock support registered
[    0.172879] MIPI CSI2 driver module loaded
[    0.175191] clocksource: Switched to clocksource mxc_timer1
[    0.175640] VFS: Disk quotas dquot_6.6.0
[    0.175842] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.199720] thermal_sys: Registered thermal governor 'step_wise'
[    0.200359] NET: Registered protocol family 2
[    0.201740] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.201833] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.201889] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.201944] TCP: Hash tables configured (established 1024 bind 1024)
[    0.202158] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.202223] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.202630] NET: Registered protocol family 1
[    0.203940] RPC: Registered named UNIX socket transport module.
[    0.203973] RPC: Registered udp transport module.
[    0.203990] RPC: Registered tcp transport module.
[    0.204005] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.205520] PCI: CLS 0 bytes, default 64
[    0.206918] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.210416] Bus freq driver module loaded
[    0.212891] Initialise system trusted keyrings
[    0.213485] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.229430] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.231087] NFS: Registering the id_resolver key type
[    0.231165] Key type id_resolver registered
[    0.231184] Key type id_legacy registered
[    0.231286] jffs2: version 2.2. (NAND)  2001-2006 Red Hat, Inc.
[    0.232514] fuse: init (API version 7.31)
[    0.324129] Key type asymmetric registered
[    0.324166] Asymmetric key parser 'x509' registered
[    0.324217] io scheduler mq-deadline registered
[    0.324239] io scheduler kyber registered
[    0.339428] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[    0.339472] imx-sdma 20ec000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx6q.bin
[    0.343848] mxs-dma 1804000.dma-apbh: initialized
[    0.351116] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX
[    0.996334] printk: console [ttymxc0] enabled
[    1.002576] imx6ul-pinctrl 20e0000.iomuxc: pin MX6UL_PAD_UART2_RX_DATA already requested by 20e0000.iomuxc; cannot claim for 21e8000.serial
[    1.015276] imx6ul-pinctrl 20e0000.iomuxc: pin-38 (21e8000.serial) status -22
[    1.022460] imx6ul-pinctrl 20e0000.iomuxc: could not request pin 38 (MX6UL_PAD_UART2_RX_DATA) from group uart2grp  on device 20e0000.iomuxc
[    1.035063] imx-uart 21e8000.serial: Error applying setting, reverse things back
[    1.042571] imx-uart: probe of 21e8000.serial failed with error -22
[    1.083162] imx_rngc 2284000.rng: Freescale RNGC registered.
[    1.089594] imx sema4 driver is registered.
[    1.120074] brd: module loaded
[    1.144016] loop: module loaded
[    1.153472] spi-nor spi2.0: found w25q256, expected n25q256a
[    1.163209] random: fast init done
[    1.169004] spi-nor spi2.0: w25q256 (32768 Kbytes)
[    1.187324] 8 fixed-partitions partitions found on MTD device 21e0000.spi
[    1.194171] Creating 8 MTD partitions on "21e0000.spi":
[    1.199604] 0x000000000000-0x000000080000 : "U-Boot"
[    1.217256] 0x000000080000-0x000000580000 : "Kernel"
[    1.237183] 0x000000580000-0x000000ea0000 : "RootFS"
[    1.257170] 0x000000ea0000-0x000001d60000 : "os_update"
[    1.277203] 0x000001d60000-0x000001f60000 : "fw_update"
[    1.297180] 0x000001f60000-0x000001fe0000 : "persist_rw"
[    1.317207] 0x000001fe0000-0x000001ff0000 : "persist_ob"
[    1.337195] 0x000001ff0000-0x000002000000 : "persist_perm"
[    1.358779] gpio@0 enforce active low on chipselect handle
[    1.369150] libphy: Fixed MDIO Bus: probed
[    1.376395] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.382273] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.389401] usbcore: registered new interface driver r8152
[    1.395038] usbcore: registered new interface driver lan78xx
[    1.400945] usbcore: registered new interface driver asix
[    1.406660] usbcore: registered new interface driver ax88179_178a
[    1.412875] usbcore: registered new interface driver cdc_ether
[    1.418946] usbcore: registered new interface driver smsc95xx
[    1.424814] usbcore: registered new interface driver net1080
[    1.430657] usbcore: registered new interface driver cdc_subset
[    1.436748] usbcore: registered new interface driver zaurus
[    1.442459] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    1.450082] usbcore: registered new interface driver cdc_ncm
[    1.455827] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.462384] ehci-pci: EHCI PCI platform driver
[    1.466994] ehci-mxc: Freescale On-Chip EHCI Host driver
[    1.472690] usbcore: registered new interface driver usb-storage
[    1.482628] imx_usb 2184000.usb: No over current polarity defined
[    1.489047] imx_usb 2184000.usb: 2184000.usb supply vbus not found, using dummy regulator
[    1.501229] ci_hdrc ci_hdrc.0: doesn't support gadget
[    1.506456] ci_hdrc ci_hdrc.0: EHCI Host Controller
[    1.511443] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[    1.545280] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[    1.551175] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    1.559553] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.566856] usb usb1: Product: EHCI Host Controller
[    1.571766] usb usb1: Manufacturer: Linux 5.4.70-2.3.0+g4f2631b022d8 ehci_hcd
[    1.578979] usb usb1: SerialNumber: ci_hdrc.0
[    1.584849] hub 1-0:1.0: USB hub found
[    1.588913] hub 1-0:1.0: 1 port detected
[    1.595650] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator
[    1.608506] ci_hdrc ci_hdrc.1: EHCI Host Controller
[    1.613504] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
[    1.645280] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[    1.651177] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    1.659560] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.666867] usb usb2: Product: EHCI Host Controller
[    1.671780] usb usb2: Manufacturer: Linux 5.4.70-2.3.0+g4f2631b022d8 ehci_hcd
[    1.678987] usb usb2: SerialNumber: ci_hdrc.1
[    1.684845] hub 2-0:1.0: USB hub found
[    1.688916] hub 2-0:1.0: 1 port detected
[    1.698343] input: 20cc000.snvs:snvs-powerkey as /devices/soc0/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
[    1.712856] read sensor who am i (0xfffffffa)error !
[    1.718066] fxls8471: probe of 0-001e failed with error -22
[    1.728847] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0
[    1.735529] i2c /dev entries driver
[    1.742261] mag3110 0-000e: 0-000e supply vdd not found, using dummy regulator
[    1.749892] mag3110 0-000e: 0-000e supply vddio not found, using dummy regulator
[    1.757532] mag3110 0-000e: check mag3110 chip ID
[    1.762728] mag3110 0-000e: read chip ID 0xfffffffa is not equal to 0xc4!
[    1.769915] mag3110: probe of 0-000e failed with error -22
[    1.778623] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[    1.787404] sdhci: Secure Digital Host Controller Interface driver
[    1.793628] sdhci: Copyright(c) Pierre Ossman
[    1.799006] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.841418] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[    1.852358] caam-snvs 20cc000.caam-snvs: violation handlers armed - init state
[    1.876316] imx6ul-pinctrl 20e0000.iomuxc: pin MX6UL_PAD_CSI_DATA04 already requested by 20e0000.iomuxc; cannot claim for 21b4000.sim
[    1.888695] imx6ul-pinctrl 20e0000.iomuxc: pin-125 (21b4000.sim) status -22
[    1.895942] imx6ul-pinctrl 20e0000.iomuxc: could not request pin 125 (MX6UL_PAD_CSI_DATA04) from group sim2grp  on device 20e0000.iomuxc
[    1.908433] mxc_sim 21b4000.sim: Error applying setting, reverse things back
[    1.916105] mxc_sim: probe of 21b4000.sim failed with error -22
[    1.923877] NET: Registered protocol family 26
[    1.930835] NET: Registered protocol family 10
[    1.938308] Segment Routing with IPv6
[    1.942370] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.950715] NET: Registered protocol family 17
[    1.956019] lib80211: common routines for IEEE802.11 drivers
[    1.961976] Key type dns_resolver registered
[    1.975683] mmc0: new high speed SDIO card at address 0001
[    1.998452] Registering SWP/SWPB emulation handler
[    2.004628] Loading compiled-in X.509 certificates
[    2.033484] regulator-can-3v3 GPIO handle specifies active low - ignored
[    2.042243] imx_thermal tempmon: Commercial CPU temperature grade - max:95C critical:90C passive:85C
[    2.052880] input: gpio_keys as /devices/soc0/gpio_keys/input/input1
[    2.060004] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:00 UTC (0)
[    2.069345] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.080791] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.087834] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.101814] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    2.109257] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[    2.120107] devtmpfs: mounted
[    2.125103] Freeing unused kernel memory: 1024K
[    2.145493] Run /init as init process

INIT: version 2.88 booting
Fuse filesystem already available.
Mounting fuse control filesystem.
Starting udev
[    3.311044] udevd[125]: starting version 3.2.8
[    3.379325] random: udevd: uninitialized urandom read (16 bytes read)
[    3.386392] random: udevd: uninitialized urandom read (16 bytes read)
[    3.392982] random: udevd: uninitialized urandom read (16 bytes read)
[    3.483857] udevd[126]: starting eudev-3.2.8
[    3.654374] cfg80211: failed to load regulatory.db
[    3.891400] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[    3.916631] imx-sdma 20ec000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx6q.bin
[    4.373508] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[    5.488981] cryptodev: loading out-of-tree module taints kernel.
[    5.501684] cryptodev: driver 1.10 loaded.
[    5.913083] wlan: Loading MWLAN driver
[    5.923266] vendor=0x02DF device=0x9149 class=0 function=1
[    5.929083] Attach moal handle ops, card interface type: 0x105
[    5.943657] SD8987: init module param from usr cfg
[    5.948579] card_type: SD8987, config block: 0
[    5.953039] cfg80211_wext=0xf
[    5.956126] wfd_name=p2p
[    5.958674] max_vir_bss=1
[    5.961299] drv_mode = 7
[    5.963836] ps_mode = 2
[    5.966322] auto_ds = 2
[    5.968777] fw_name=nxp/sdiouart8987_combo_v0.bin
[    5.973488] cal_data_cfg=nxp/WlanCalData_ext_Billy_P0_revA_CapCode_C3.conf
[    5.980426] txpwrlimit_cfg=nxp/txpower_US.bin
[    5.984823] SDIO: max_segs=128 max_seg_size=65535
[    5.989631] rx_work=0 cpu_num=1
[    5.992839] Attach mlan adapter operations.card_type is 0x105.
[    6.005302] wlan: Enable TX SG mode
[    6.008820] wlan: Enable RX SG mode
[    6.015415] Request firmware: nxp/sdiouart8987_combo_v0.bin
[    6.710399] Wlan: FW download over, firmwarelen=528176 downloaded 528176
[    7.555789] WLAN FW is active
[    7.558837] on_time is 7553687042
[    7.709961] fw_cap_info=0x181c3f0b, dev_cap_mask=0xffffdbff
[    7.715769] max_p2p_conn = 8, max_sta_conn = 8
[    7.764110] wlan: version = SD8987---16.92.10.p209-MXM5X16215.p2-GPL-(FP92) 
[    7.791402] wlan: Driver loaded successfully
hwclock: settimeofday: Invalid argument
Tue Nov 23 21:05:09 UTC 2021
[    8.601240] urandom_read: 1 callbacks suppressed
[    8.601254] random: dd: uninitialized urandom read (512 bytes read)

INIT: Entering runlevel: 5
Configuring network interfaces... done.
[    8.805774] random: dbus-uuidgen: uninitialized urandom read (12 bytes read)
[    8.812929] random: dbus-uuidgen: uninitialized urandom read (8 bytes read)
Starting system message bus: dbus.
Starting ntpd: done
Starting syslogd/klogd: done
Starting Blink: [    9.596584] Check for update
4096+0 records in
4096+0 records out
tar: invalid magic
tar: short read
tar: sm.tar.gz: not found in archive
[    9.930550] Blink FACTORY
FACTORY INFO  (lly/fwup.c:  48) [21:05:10.181]HASH: 0b2c5713
INFO  (lly/fwup.c:  48) [21:05:10.182]HASH: 7db95926
INFO  (lly/fwup.c:  48) [21:05:10.182]HASH: 450cb4b7
INFO  (lly/fwup.c:  48) [21:05:10.183]HASH: e75d0c74
INFO  (lly/fwup.c:  48) [21:05:10.183]HASH: 3fcd4579
INFO  (lly/fwup.c:  48) [21:05:10.183[   10.210116] Blink VALIDATED
]HASH: 844e9710
INFO  (lly/fwup.c:  48) [21:05:10.184]HASH: 16933373
INFO  (lly/fwup.c:  48) [21:05:10.192]HASH: 85382906
INFO  (lly/fwup.c: 257) [21:05:10.204]/smapp/key0.der ret=0
VALID .

INIT: [   10.487662] us_mode
[   10.489843] Board ID: 3
[   10.492383] chip reset
no more processes left in this runlevel[   10.531400] si4455_ioctl version: 1.61

[   10.556339] Starting SMAPP
INFO  (pp/smapp.c: 444) [21:05:10.564]STARTUP IMMI 33
ERROR (rsist_rw.c:  77) [21:05:10.564]Cannot open /persist/persist_sm.log
INFO  (util/log.c: 458) [21:05:10.565]unable to access persistent log file [-3]
INFO  (_encrypt.c:  50) [21:05:10[   10.595297] random: crng init done
[   10.600033] random: 2 urandom warning(s) missed due to ratelimiting
.590]Got cbc(aes) with driver cbc-aes-dcp
WARN  (rsist_ob.c:  85) [21:05:10.603]Invalid data in OB
INFO  (rsist_ob.c: 190) [21:05:10.603]Falling back to v1 persist_ob
WARN  (rsist_ob.c: 155) [21:05:10.611]Invalid data in OB
WARN  (pp/smapp.c:1965) [21:05:10.612]File Not found /tmp/ap_mode
INFO  (tton_mgr.c: 152) [21:05:10.612]Initialized button press detection
INFO [   10.636234] wlan: Unloading MWLAN driver
 (pp/smapp.c: 496) [21:05:10.622][   10.643322] Station already not in enhanced deep sleep mode
OS 5.5.9 FW 15.9.10 DRV 1.61
INFO  (cs/imssl.c: 137) [21:05:10.627]Loading client cert into imssl context
ERROR (rsist_rw.c:  77) [21:05:10.627]Cannot open /persist/ls_key.pem
ERROR (rsist_rw.c:  77) [21:05:10.627]Cannot open /persist/ls_cert.der
INFO  (pp/smapp.c: 549) [21:05:10.627]cam2sm key/cert -3 -3
INFO  (s_config.c:  35) [21:05:10.627]Command to run: rmmod moal
[   10.945730] Free module params
[   10.949181] wlan: Driver unloaded
INFO  (util/sys.c:  49) [21:05:10.985]Command was run: rmmod moal Status: 0
INFO  (s_config.c:  36) [21:05:10.985]Command to run: rmmod mlan
INFO  (util/sys.c:  49) [21:05:11.027]Command was run: rmmod mlan Status: 0
INFO  (s_config.c:  37) [21:05:11.028]Command to run: modprobe mlan
INFO  (util/sys.c:  49) [21:05:11.070]Command was run: modprobe mlan Status: 0
INFO  (s_config.c:  38) [21:05:11.070]Command to run: modprobe moal dev_cap_mask=0xffffdbff mod_para=nxp/wifi_mod_para_EU.conf
[   11.127606] wlan: Loading MWLAN driver
[   11.137684] vendor=0x02DF device=0x9149 class=0 function=1
[   11.143343] Attach moal handle ops, card interface type: 0x105
[   11.157053] SD8987: init module param from usr cfg
[   11.161884] card_type: SD8987, config block: 0
[   11.166843] cfg80211_wext=0xf
[   11.169835] wfd_name=p2p
[   11.172376] max_vir_bss=1
[   11.175000] drv_mode = 7
[   11.178116] ps_mode = 2
[   11.180579] auto_ds = 2
[   11.183035] fw_name=nxp/sdiouart8987_combo_v0.bin
[   11.188158] cal_data_cfg=nxp/WlanCalData_ext_Billy_P0_revA_CapCode_C3.conf
[   11.195049] txpwrlimit_cfg=nxp/txpower_EU.bin
[   11.200981] SDIO: max_segs=128 max_seg_size=65535
[   11.206024] rx_work=0 cpu_num=1
[   11.209225] Attach mlan adapter operations.card_type is 0x105.
[   11.221589] wlan: Enable TX SG mode
[   11.225111] wlan: Enable RX SG mode
[   11.235456] Request firmware: nxp/sdiouart8987_combo_v0.bin
[   11.243694] WLAN FW already running! Skip FW download
[   11.248942] WLAN FW is active
[   11.251924] on_time is 11246787292
[   11.389837] fw_cap_info=0x181c3f0b, dev_cap_mask=0xffffdbff
[   11.395656] max_p2p_conn = 8, max_sta_conn = 8
[   11.454055] wlan: version = SD8987---16.92.10.p209-MXM5X16215.p2-GPL-(FP92) 
[   11.479832] wlan: Driver loaded successfully
INFO  (util/sys.c:  49) [21:05:11.490]Command was run: modprobe moal dev_cap_mask=0xffffdbff mod_para=nxp/wifi_mod_para_EU.conf Status: 0
INFO  (s_config.c:  42) [21:05:11.490]Command to run: /usr/share/nxp_wireless/bin_mxm_wifiex/mlanutl mlan0 countrycode EU
INFO  (util/sys.c:  49) [21:05:11.535]Command was run: /usr/share/nxp_wireless/bin_mxm_wifiex/mlanutl mlan0 countrycode EU Status: 0
INFO  (s_config.c:  43) [21:05:11.535]Command to run: /usr/share/nxp_wireless/bin_mxm_wifiex/mlanutl mlan0 hostcmd /lib/firmware/nxp/ed_mac_ctrl_V3[   11.563163] WDIOC_SETTIMEOUT(14400)
_8987.conf ed_mac_ctrl_v3
INFO  (util/sys.c:  45) [21:05:11.541]HOSTCMD_RESP: CmdCode=0x130, Size=0x14, SeqNum=0x22, Result=0000
INFO  (util/sys.c:  45) [21:05:11.541]payload: len=12
INFO  (util/sys.c:  45) [21:05:11.542]01 00 06 00 01 00 06 00 ff 00 00 00
INFO  (util/sys.c:  45) [21:05:11.542]
INFO  (util/sys.c:  49) [21:05:11.543]Command was run: /usr/share/nxp_wireless/bin_mxm_wifiex/mlanutl mlan0 hostcmd /lib/firmware/nxp/ed_mac_ctrl_V3_8987.conf ed_mac_ctrl_v3 Status: 0
INFO  (s_config.c:  60) [21:05:11.543]Command to run: ifconfig mlan0 hw ether 9c:c8:e9:74:e5:b2
INFO  (util/sys.c:  49) [21:05:11.550]Command was run: ifconfig mlan0 hw ether 9c:c8:e9:74:e5:b2 Status: 0
INFO  (s_config.c:  64) [21:05:11.551]Command to run: ifconfig uap0 hw ether 9c:c8:e9:74:e5:b2
INFO  (util/sys.c:  49) [21:05:11.557]Command was run: ifconfig uap0 hw ether 9c:c8:e9:74:e5:b2 Status: 0
INFO  (k_listen.c: 617) [21:05:11.567]sock worker [76948d7c]
INFO  (   ob/ob.c: 217) [21:05:11.569]Initializing OB SEM
INFO  (   ob/ob.c: 286) [21:05:11.570]Encryption suite set to version 2
INFO  (pd/httpd.c: 376) [21:05:11.571]Server ready to accept connection
INFO  (  cs/net.c: 243) [21:05:13.573]we version compiled value = 22
[   15.067681] wlan: SCAN COMPLETED: scanned AP count=14
INFO  (ndpoints.c: 287) [21:05:15.581]Log length 3747 3747
INFO  (ndpoints.c: 295) [21:05:15.582]len less than than 4000 bytes, but greater than 100
INFO  (ndpoints.c: 304) [21:05:15.591]Wanted to read 3647 bytes. Read 3647 bytes
INFO  (/imcjson.c: 134) [21:05:15.616]Found carriage returns: 71
INFO  (/imcjson.c: 135) [21:05:15.616]Found new lines: 48
INFO  (s_config.c: 120) [21:05:15.616]Command to run: rm -rf /tmp/dnsmasq.d
INFO  (util/sys.c:  49) [21:05:15.622]Command was run: rm -rf /tmp/dnsmasq.d Status: 0
INFO  (s_config.c: 121) [21:05:15.622]Command to run: rm /tmp/dhcp.leases
INFO  (util/sys.c:  45) [21:05:15.627]rm: can't remove '/tmp/dhcp.leases': No such file or directory
INFO  (util/sys.c:  49) [21:05:15.628]Command was run: rm /tmp/dhcp.leases Status: 256
INFO  (s_config.c: 122) [21:05:15.628]Command to run: rm /tmp/resolv.conf.auto
INFO  (util/sys.c:  45) [21:05:15.634]rm: can't remove '/tmp/resolv.conf.auto': No such file or directory
INFO  (util/sys.c:  49) [21:05:15.635]Command was run: rm /tmp/resolv.conf.auto Status: 256
INFO  (s_config.c: 123) [21:05:15.635]Command to run: rm /tmp/hosts
INFO  (util/sys.c:  45) [21:05:15.640]rm: can't remove '/tmp/hosts': No such file or directory
INFO  (util/sys.c:  49) [21:05:15.642]Command was run: rm /tmp/hosts Status: 256
INFO  (   ob/ob.c: 705) [21:05:15.642]Starting AP mode: BLINK-119F
INFO  (s_config.c: 128) [21:05:15.642]Command to run: /etc/init.d/dnsmasq stop
INFO  (util/sys.c:  45) [21:05:15.688]stopping DNS forwarder and DHCP server: dnsmasq... no /usr/bin/dnsmasq found; none killed
INFO  (util/sys.c:  49) [21:05:15.690]Command was run: /etc/init.d/dnsmasq stop Status: 256
INFO  (s_config.c: 129) [21:05:15.690]Command to run: ifdown mlan0
INFO  (util/sys.c:  45) [21:05:15.696]ifdown: interface mlan0 not configured
INFO  (util/sys.c:  49) [21:05:15.697]Command was run: ifdown mlan0 Status: 0
INFO  (s_config.c: 131) [21:05:15.697]Command to run: mkdir /tmp/dnsmasq.d
INFO  (util/sys.c:  49) [21:05:15.703]Command was run: mkdir /tmp/dnsmasq.d Status: 0
INFO  (s_config.c: 132) [21:05:15.703]Command to run: touch /tmp/dhcp.leases
INFO  (util/sys.c:  49) [21:05:15.709]Command was run: touch /tmp/dhcp.leases Status: 0
INFO  (s_config.c: 133) [21:05:15.709]Command to run: touch /tmp/resolv.conf.auto
INFO  (util/sys.c:  49) [21:05:15.717]Command was run: touch /tmp/resolv.conf.auto Status: 0
INFO  (s_config.c: 134) [21:05:15.717]Command to run: touch /tmp/hosts
INFO  (util/sys.c:  49) [21:05:15.726]Command was run: touch /tmp/hosts Status: 0
INFO  (s_config.c: 141) [21:05:15.726]Command to run: cp /root/config/dnsmasq.conf /etc/dnsmasq.conf
INFO  (util/sys.c:  49) [21:05:15.733]Command was run: cp /root/config/dnsmasq.conf /etc/dnsmasq.conf Status: 0
INFO  (s_config.c: 150) [21:05:15.733]Command to run: ifup uap0
INFO  (util/sys.c:  45) [21:05:16.112]Starting HOSTAP Daemon: Configuration file: /etc/hostapd.conf
INFO  (util/sys.c:  45) [21:05:16.167]rfkill: Cannot open RFKILL control device
INFO  (util/sys.c:  45) [21:05:16.170]uap0: interface state UNINITIALIZED->COUNTRY_UPDATE
INFO  (util/sys.c:  45) [21:05:16.173]hostapd.
INFO  (util/sys.c:  45) [21:05:16.279]starting DNS forwarder and DHCP server: dnsmasq... done.
INFO  (util/sys.c:  49) [21:05:16.289]Command was run: ifup uap0 Status: 0
INFO  (   ob/ob.c: 711) [21:05:16.289]Command to run: /root/apps/led_controller/led_controller 24
INFO  (util/sys.c:  49) [21:05:16.304]Command was run: /root/apps/led_controller/led_controller 24 Status: 0
INFO  (   ob/ob.c: 715) [21:05:16.304]AP mode active
[   21.190056] wlan: Starting AP
[   21.194031] Get ht_cap from beacon ies: 0xc
[   21.200118] fw doesn't support 11ax
[   21.213433] wlan: AP started
[   21.216804] IPv6: ADDRCONF(NETDEV_CHANGE): uap0: link becomes ready
[   21.225535] Set AC=3, txop=47 cwmin=3, cwmax=7 aifs=1
[   21.233901] Set AC=2, txop=94 cwmin=7, cwmax=15 aifs=1
[   21.241704] Set AC=0, txop=0 cwmin=15, cwmax=63 aifs=3
[   21.249909] Set AC=1, txop=0 cwmin=15, cwmax=1023 aifs=7
[   32.485380] can-3v3: disabling