bruvv

Note: this was tested and used on DSM5 and partly on 6. Since V7 I am not using this anymore.

Got and ssh into your box. Find what is using swap:

find /proc -maxdepth 2 -path "/proc/[0-9]*/status" -readable -exec awk -v FS=":" -v TOTSWP="$(cat /proc/swaps | sed 1d | awk 'BEGIN{sum=0} {sum=sum+$(NF-2)} END{print sum}')" '{process[$1]=$2;sub(/^[ \t]+/,"",process[$1]);} END {if(process["VmSwap"] && process["VmSwap"] != "0 kB") {used_swap=process["VmSwap"];sub(/[ a-zA-Z]+/,"",used_swap);percent=(used_swap/TOTSWP*100); printf "%10s %-30s %20s %6.2f%\n",process["Pid"],process["Name"],process["VmSwap"],percent} }' '{}' \;  | awk '{print $(NF-2),$0}' | sort -hr | head | cut -d " " -f2-

Update synoinfo.conf to correct memory in MB (https://www.gbmb.org/gb-to-mb) for 8GB:

ophilips

# Xiaomi HomeKit
fan:
  - platform: template
    fans:
      xiaomi_fan:
        friendly_name: "Xiaomi Vacuum"
        value_template: "{%if states('vacuum.xiaomi_vacuum_cleaner') == 'cleaning' %}on{%elif states('vacuum.xiaomi_vacuum_cleaner') == 'paused' %}on{%else %}off{% endif %}"
        speed_template: "{{ state_attr('vacuum.xiaomi_vacuum_cleaner', 'fan_speed') }}"
        turn_on:
          service: vacuum.start

nicman23

#!/bin/sh /etc/rc.common

START=99
USE_PROCD=1

start_service() {
  if [ -e /root/.upgrade ]
    then exit
    else touch /root/.upgrade
  fi

clivetyphon

Easy client VPN for all major platforms using strongSwan IPsec

Overview

The goal here is to provide quick and easy but secure client VPN that can be configured natively without any additional software on:

• Linux
• iOS
• Android
• Windows
• OSX

jwalanta

Add the following line in /etc/dnsmasq.conf

dhcp-script=/etc/detect_new_device.sh

Setup sendmail to send email to your text number.

Reference:

• https://wiki.openwrt.org/doc/howto/smtp.client

samuelcolvin

Use the Hubble app to get the camera connected to a wifi network.

Find the Camera's IP address:

> sudo arp-scan --interface=enp3s0 --localnet
Interface: enp3s0, datalink type: EN10MB (Ethernet)
Starting arp-scan 1.8.1 with 256 hosts (http://www.nta-monitor.com/tools/arp-scan/)
192.168.1.100	00:19:99:0f:6a:98	Fujitsu Technology Solutions
192.168.1.102	c4:6e:1f:53:f0:8b	(Unknown)

Weeker

<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
	<key>PayloadContent</key>
	<array>
		<dict>
			<key>IKEv2</key>
			<dict>
				<key>AuthName</key>

gbaman

Raspberry Pi Zero OTG Mode

Simple guide for setting up OTG modes on the Raspberry Pi Zero - By Andrew Mulholland (gbaman).

The Raspberry Pi Zero (and model A and A+) support USB On The Go, given the processor is connected directly to the USB port, unlike on the B, B+ or Pi 2 B, which goes via a USB hub.
Because of this, if setup to, the Pi can act as a USB slave instead, providing virtual serial (a terminal), virtual ethernet, virtual mass storage device (pendrive) or even other virtual devices like HID, MIDI, or act as a virtual webcam!
It is important to note that, although the model A and A+ can support being a USB slave, they are missing the ID pin (is tied to ground internally) so are unable to dynamically switch between USB master/slave mode. As such, they default to USB master mode. There is no easy way to change this right now.
It is also important to note, that a USB to UART serial adapter is not needed for any of these guides, as may be documented elsewhere across the int