Created
November 20, 2022 03:14
-
-
Save pinuke/d99b047edde566f91502c9db8c41abc4 to your computer and use it in GitHub Desktop.
Rock Pi 4 stuck during boot up
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| In | |
| channel 0 | |
| CS = 0 | |
| MR0=0x19 | |
| MR4=0x3 | |
| MR5=0x6 | |
| MR8=0x10 | |
| MR12=0x72 | |
| MR14=0x72 | |
| MR18=0x0 | |
| MR19=0x0 | |
| MR24=0x8 | |
| MR25=0xFF | |
| channel 1 | |
| CS = 0 | |
| MR0=0x19 | |
| MR4=0x3 | |
| MR5=0x6 | |
| MR8=0x10 | |
| MR12=0x72 | |
| MR14=0x72 | |
| MR18=0x0 | |
| MR19=0x0 | |
| MR24=0x8 | |
| MR25=0xFF | |
| channel 0 training pass! | |
| channel 1 training pass! | |
| change freq to 416MHz 0,1 | |
| Channel 0: LPDDR4,416MHz | |
| Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB | |
| Channel 1: LPDDR4,416MHz | |
| Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB | |
| 256B stride | |
| channel 0 | |
| CS = 0 | |
| MR0=0x19 | |
| MR4=0x3 | |
| MR5=0x6 | |
| MR8=0x10 | |
| MR12=0x72 | |
| MR14=0x72 | |
| MR18=0x0 | |
| MR19=0x0 | |
| MR24=0x8 | |
| MR25=0xFF | |
| channel 1 | |
| CS = 0 | |
| MR0=0x19 | |
| MR4=0x3 | |
| MR5=0x6 | |
| MR8=0x10 | |
| MR12=0x72 | |
| MR14=0x72 | |
| MR18=0x0 | |
| MR19=0x0 | |
| MR24=0x8 | |
| MR25=0xFF | |
| channel 0 training pass! | |
| channel 1 training pass! | |
| channel 0, cs 0, advanced training done | |
| channel 1, cs 0, advanced training done | |
| change freq to 666MHz 1,0 | |
| ch 0 ddrconfig = 0x101, ddrsize = 0x40 | |
| ch 1 ddrconfig = 0x101, ddrsize = 0x40 | |
| pmugrf_os_reg[2] = 0x32C1F2C1, stride = 0xD | |
| ddr_set_rate to 328MHZ | |
| ddr_set_rate to 666MHZ | |
| ddr_set_rate to 416MHZ, ctl_index 0 | |
| ddr_set_rate to 666MHZ, ctl_index 1 | |
| support 416 328 666 MHz, current 666MHz | |
| OUT | |
| Boot1: 2019-03-14, version: 1.19 | |
| CPUId = 0x0 | |
| ChipType = 0x10, 267 | |
| mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 | |
| mmc: ERROR: Card did not respond to voltage select! | |
| emmc reinit | |
| mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 | |
| mmc: ERROR: Card did not respond to voltage select! | |
| emmc reinit | |
| mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 | |
| mmc: ERROR: Card did not respond to voltage select! | |
| SdmmcInit=2 1 | |
| mmc0:cmd5,20 | |
| SdmmcInit=0 0 | |
| BootCapSize=0 | |
| UserCapSize=60874MB | |
| FwPartOffset=2000 , 0 | |
| StorageInit ok = 45441 | |
| SecureMode = 0 | |
| SecureInit read PBA: 0x4 | |
| SecureInit read PBA: 0x404 | |
| SecureInit read PBA: 0x804 | |
| SecureInit read PBA: 0xc04 | |
| SecureInit read PBA: 0x1004 | |
| SecureInit read PBA: 0x1404 | |
| SecureInit read PBA: 0x1804 | |
| SecureInit read PBA: 0x1c04 | |
| SecureInit ret = 0, SecureMode = 0 | |
| atags_set_bootdev: ret:(0) | |
| GPT part: 0, name: loader1, start:0x40, size:0x1f40 | |
| GPT part: 1, name: loader2, start:0x4000, size:0x2000 | |
| GPT part: 2, name: trust, start:0x6000, size:0x2000 | |
| GPT part: 3, name: boot, start:0x8000, size:0x100000 | |
| GPT part: 4, name: rootfs, start:0x108000, size:0x66b573 | |
| no find partition:uboot. | |
| LoadTrust Addr:0x4000 | |
| No find bl30.bin | |
| No find bl32.bin | |
| Load uboot, ReadLba = 2000 | |
| hdr 0000000003380880 + 0x0:0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0 | |
| 0,0x00,0x00,0x00,0x00,0x00, | |
| Load OK, addr=0x200000, size=0xf14cc | |
| RunBL31 0x40000 | |
| NOTICE: BL31: v1.3(release):845ee93 | |
| NOTICE: BL31: Built : 15:51:11, Jul 22 2020 | |
| NOTICE: BL31: Rockchip release version: v1.1 | |
| INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 | |
| INFO: Using opteed sec cpu_context! | |
| INFO: boot cpu mask: 0 | |
| INFO: plat_rockchip_pmu_init(1196): pd status 3e | |
| INFO: BL31: Initializing runtime services | |
| WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE init | |
| ialization. SMC`s destined for OPTEE will return SMC_UNK | |
| ERROR: Error initializing runtime service opteed_fast | |
| INFO: BL31: Preparing for EL3 exit to normal world | |
| INFO: Entry point address = 0x200000 | |
| INFO: SPSR = 0x3c9 | |
| U-Boot 2017.09-00028-g8e67d58161 (Oct 19 2022 - 10:11:41 +0800) | |
| Model: Radxa ROCK 4C+ | |
| PreSerial: 2 | |
| DRAM: 3.9 GiB | |
| Relocation Offset is: f5bdd000 | |
| Sysmem: init | |
| I2c speed: 400000Hz | |
| PMIC: RK8090 (on=0x69, off=0x02) | |
| vdd_log 900000 uV | |
| vdd_cpu_l 900000 uV | |
| MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0 | |
| Using default environment | |
| Failed to found available display route | |
| Failed to found available display route | |
| Model: Radxa ROCK 4C+ | |
| Bootdev(atags): mmc 1 | |
| PartType: EFI | |
| get part misc fail -1 | |
| boot mode: None | |
| CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A) | |
| CLK: (uboot. armb: enter 24000 KHz, init 24000 KHz, kernel 0N/A) | |
| aplll 816000 KHz | |
| apllb 24000 KHz | |
| dpll 666000 KHz | |
| cpll 24000 KHz | |
| gpll 800000 KHz | |
| npll 600000 KHz | |
| vpll 24000 KHz | |
| aclk_perihp 133333 KHz | |
| hclk_perihp 66666 KHz | |
| pclk_perihp 33333 KHz | |
| aclk_perilp0 266666 KHz | |
| hclk_perilp0 88888 KHz | |
| pclk_perilp0 44444 KHz | |
| hclk_perilp1 100000 KHz | |
| pclk_perilp1 50000 KHz | |
| Net: eth0: ethernet@fe300000 | |
| Hit key to stop autoboot('CTRL+C'): 0 | |
| Here trying to boot from nvme | |
| dcache off | |
| Device 0: unknown device | |
| switch to partitions #0, OK | |
| mmc1 is current device | |
| Scanning mmc 1:4... | |
| Found /extlinux/extlinux.conf | |
| pxefile_addr_str = 0x00500000 | |
| bootfile = /extlinux/extlinux.conf | |
| Retrieving file: /extlinux/extlinux.conf | |
| reading /extlinux/extlinux.conf | |
| 449 bytes read in 5 ms (86.9 KiB/s) | |
| Retrieving file: /hw_intfc.conf | |
| reading /hw_intfc.conf | |
| 2277 bytes read in 4 ms (555.7 KiB/s) | |
| hw_parse_property: illegal line | |
| hw_parse_property: illegal line | |
| dtoverlay number: 0, name:/overlays/console-on-ttyS2.dtbo | |
| hw_conf.valid = 1 | |
| hw_conf.pwm0 = 0 | |
| hw_conf.pwm1 = 0 | |
| hw_conf.uart2 = 0 | |
| hw_conf.uart4 = 0 | |
| hw_conf.spi1 = 0 | |
| hw_conf.spi2 = 0 | |
| hw_conf.i2c2 = 0 | |
| hw_conf.i2c6 = 0 | |
| hw_conf.i2c7 = 0 | |
| hw_conf.dts_overlay_count = 1 | |
| hw_conf.dts_overlay[0] = /overlays/console-on-ttyS2.dtbo | |
| 1: kernel-4.4.194-11-rk3399-rockchip-g1bb08d49cc40 | |
| Retrieving file: /initrd.img-4.4.194-11-rk3399-rockchip-g1bb08d49cc40 | |
| reading /initrd.img-4.4.194-11-rk3399-rockchip-g1bb08d49cc40 | |
| 19582211 bytes read in 838 ms (22.3 MiB/s) | |
| Retrieving file: /vmlinuz-4.4.194-11-rk3399-rockchip-g1bb08d49cc40 | |
| reading /vmlinuz-4.4.194-11-rk3399-rockchip-g1bb08d49cc40 | |
| 16756744 bytes read in 717 ms (22.3 MiB/s) | |
| append: earlyprintk console=ttyFIQ0,1500000n8 rw init=/sbin/init rootfstype=ext4 | |
| rootwait root=UUID=36c6d71f-716f-4efa-8dab-18225508dac2 console=ttyS2,1500000n | |
| 8 | |
| Retrieving file: /dtbs/4.4.194-11-rk3399-rockchip-g1bb08d49cc40/rockchip/rk3399- | |
| rock-4c-plus.dtb | |
| reading /dtbs/4.4.194-11-rk3399-rockchip-g1bb08d49cc40/rockchip/rk3399-rock-4c-p | |
| lus.dtb | |
| 101509 bytes read in 22 ms (4.4 MiB/s) | |
| fdt addr 0000000008300000 | |
| fdt magic number edfe0dd0 | |
| fdt size 1048576 | |
| merge_dts_overlay | |
| Retrieving file: /overlays/console-on-ttyS2.dtbo | |
| reading /overlays/console-on-ttyS2.dtbo | |
| 774 bytes read in 6 ms (126 KiB/s) | |
| overlay dtb(0x0000000008200000) is valid | |
| fdt_overlay_apply 0000000008300000 0000000008200000 | |
| ## Flattened Device Tree blob at 08300000 | |
| Booting using the fdt blob at 0x8300000 | |
| 'reserved-memory' ramoops@110000: addr=110000 size=f0000 | |
| Loading Ramdisk to e8b16000, end e9dc2d03 ... OK | |
| Loading Device Tree to 00000000e8a13000, end 00000000e8b15fff ... OK | |
| Adding bank: 0x00200000 - 0xf8000000 (size: 0xf7e00000) | |
| Total: 10895.713 ms | |
| Starting kernel ... | |
| [ 0.000000] Booting Linux on physical CPU 0x0 | |
| [ 0.000000] Initializing cgroup subsys cpuset | |
| [ 0.000000] Initializing cgroup subsys cpu | |
| [ 0.000000] Initializing cgroup subsys cpuacct | |
| [ 0.000000] Linux version 4.4.194-11-rk3399-rockchip-g1bb08d49cc40 (stephen@m | |
| rs-ella) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfb | |
| c167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP Fri Nov 4 21:33:40 | |
| CST 2022 | |
| [ 0.000000] Boot CPU: AArch64 Processor [410fd034] | |
| [ 0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@0000 | |
| 0000': base 0x0000000000000000, size 0 MiB | |
| [ 0.000000] cma: Reserved 16 MiB at 0x00000000f7000000 | |
| [ 0.000000] psci: probing for conduit method from DT. | |
| [ 0.000000] psci: PSCIv1.0 detected in firmware. | |
| [ 0.000000] psci: Using standard PSCI v0.2 function IDs | |
| [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. | |
| [ 0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc0f6ed1000 s45928 r8192 d318 | |
| 96 u86016 | |
| [ 0.000000] Detected VIPT I-cache on CPU0 | |
| [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 | |
| [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag | |
| es: 999432 | |
| [ 0.000000] Kernel command line: earlyprintk console=ttyFIQ0,1500000n8 rw ini | |
| t=/sbin/init rootfstype=ext4 rootwait root=UUID=36c6d71f-716f-4efa-8dab-1822550 | |
| 8dac2 console=ttyS2,1500000n8 | |
| [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) | |
| [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes | |
| ) | |
| [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) | |
| [ 0.000000] software IO TLB: mapped [mem 0xee600000-0xf2600000] (64MB) | |
| [ 0.000000] Memory: 3869644K/4061184K available (9790K kernel code, 1516K rwd | |
| ata, 3996K rodata, 1024K init, 661K bss, 175156K reserved, 16384K cma-reserved) | |
| [ 0.000000] Virtual kernel memory layout: | |
| [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 M | |
| B) | |
| [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 G | |
| B) | |
| [ 0.000000] .init : 0xffffff8008e00000 - 0xffffff8008f00000 ( 1024 K | |
| B) | |
| [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008a10000 ( 9792 K | |
| B) | |
| [ 0.000000] .rodata : 0xffffff8008a10000 - 0xffffff8008e00000 ( 4032 K | |
| B) | |
| [ 0.000000] .data : 0xffffff8008f00000 - 0xffffff800907b008 ( 1517 K | |
| B) | |
| [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 G | |
| B maximum) | |
| [ 0.000000] 0xffffffbdc0008000 - 0xffffffbdc3e00000 ( 61 M | |
| B actual) | |
| [ 0.000000] fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 ( 4116 K | |
| B) | |
| [ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 M | |
| B) | |
| [ 0.000000] memory : 0xffffffc000200000 - 0xffffffc0f8000000 ( 3966 M | |
| B) | |
| [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 | |
| [ 0.000000] Hierarchical RCU implementation. | |
| [ 0.000000] Build-time adjustment of leaf fanout to 64. | |
| [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6. | |
| [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6 | |
| [ 0.000000] NR_IRQS:64 nr_irqs:64 0 | |
| [ 0.000000] GIC: Using split EOI/Deactivate mode | |
| [ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000 | |
| [ 0.000000] ITS: allocated 65536 Devices @ee000000 (psz 64K, shr 0) | |
| [ 0.000000] ITS: using cache flushing for cmd queue | |
| [ 0.000000] GIC: using LPI property table @0x00000000ee080000 | |
| [ 0.000000] ITS: Allocated 1792 chunks for LPIs | |
| [ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000 | |
| [ 0.000000] CPU0: using LPI pending table @0x00000000ee090000 | |
| [ 0.000000] GIC: using cache flushing for LPI property table | |
| [ 0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpu | |
| s/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] } | |
| [ 0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /c | |
| pus/cpu@101[5] } | |
| [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac | |
| as parent of dclk_vop0, rate changes may not work | |
| [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac | |
| as parent of dclk_vop1, rate changes may not work | |
| [ 0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31 | |
| [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). | |
| [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: | |
| 0x588fe9dc0, max_idle_ns: 440795202592 ns | |
| [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 | |
| 46511097ns | |
| [ 0.001458] Console: colour dummy device 80x25 | |
| [ 0.001486] Calibrating delay loop (skipped), value calculated using timer fr | |
| equency.. 48.00 BogoMIPS (lpj=24000) | |
| [ 0.001499] pid_max: default: 32768 minimum: 301 | |
| [ 0.001661] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) | |
| [ 0.001673] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) | |
| [ 0.002445] Initializing cgroup subsys memory | |
| [ 0.002480] Initializing cgroup subsys devices | |
| [ 0.002493] Initializing cgroup subsys freezer | |
| [ 0.002510] Initializing cgroup subsys net_cls | |
| [ 0.002522] Initializing cgroup subsys perf_event | |
| [ 0.002536] Initializing cgroup subsys pids | |
| [ 0.002582] ftrace: allocating 36819 entries in 144 pages | |
| [ 0.092534] sched-energy: Sched-energy-costs installed from DT | |
| [ 0.092551] CPU0: update cpu_capacity 401 | |
| [ 0.092612] ASID allocator initialised with 32768 entries | |
| [ 0.095107] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee2 | |
| 0000 domain created | |
| [ 0.095636] Platform MSI: /interrupt-controller@fee00000/interrupt-controller | |
| @fee20000 domain created | |
| [ 0.097048] Detected VIPT I-cache on CPU1 | |
| [ 0.097085] CPU1: found redistributor 1 region 0:0x00000000fef20000 | |
| [ 0.097115] CPU1: using LPI pending table @0x00000000ee290000 | |
| [ 0.097173] CPU1: update cpu_capacity 401 | |
| [ 0.097177] CPU1: Booted secondary processor [410fd034] | |
| [ 0.097970] Detected VIPT I-cache on CPU2 | |
| [ 0.098002] CPU2: found redistributor 2 region 0:0x00000000fef40000 | |
| [ 0.098033] CPU2: using LPI pending table @0x00000000ee2c0000 | |
| [ 0.098085] CPU2: update cpu_capacity 401 | |
| [ 0.098089] CPU2: Booted secondary processor [410fd034] | |
| [ 0.098882] Detected VIPT I-cache on CPU3 | |
| [ 0.098913] CPU3: found redistributor 3 region 0:0x00000000fef60000 | |
| [ 0.098943] CPU3: using LPI pending table @0x00000000ee320000 | |
| [ 0.098993] CPU3: update cpu_capacity 401 | |
| [ 0.098997] CPU3: Booted secondary processor [410fd034] | |
| [ 0.099783] Detected PIPT I-cache on CPU4 | |
| [ 0.099806] CPU4: found redistributor 100 region 0:0x00000000fef80000 | |
| [ 0.099841] CPU4: using LPI pending table @0x00000000ee350000 | |
| [ 0.099876] CPU4: update cpu_capacity 1024 | |
| [ 0.099879] CPU4: Booted secondary processor [410fd082] | |
| [ 0.100528] Detected PIPT I-cache on CPU5 | |
| [ 0.100551] CPU5: found redistributor 101 region 0:0x00000000fefa0000 | |
| [ 0.100588] CPU5: using LPI pending table @0x00000000ee380000 | |
| [ 0.100622] CPU5: update cpu_capacity 1024 | |
| [ 0.100626] CPU5: Booted secondary processor [410fd082] | |
| [ 0.100740] Brought up 6 CPUs | |
| [ 0.100823] SMP: Total of 6 processors activated. | |
| [ 0.100832] CPU features: detected feature: GIC system register CPU interface | |
| [ 0.100842] CPU features: detected feature: 32-bit EL0 Support | |
| [ 0.100853] CPU: All CPU(s) started at EL2 | |
| [ 0.100899] alternatives: patching kernel code | |
| [ 0.102258] devtmpfs: initialized | |
| [ 0.125854] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma | |
| x_idle_ns: 1911260446275000 ns | |
| [ 0.125877] futex hash table entries: 2048 (order: 5, 131072 bytes) | |
| [ 0.126605] pinctrl core: initialized pinctrl subsystem | |
| [ 0.128297] Failed to find legacy iommu devices | |
| [ 0.128698] NET: Registered protocol family 16 | |
| [ 0.133603] cpuidle: using governor ladder | |
| [ 0.137610] cpuidle: using governor menu | |
| [ 0.137635] Registered FIQ tty driver | |
| [ 0.137821] vdso: 2 pages (1 code @ ffffff8008a16000, 1 data @ ffffff8008f040 | |
| 00) | |
| [ 0.137853] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. | |
| [ 0.138639] DMA: preallocated 256 KiB pool for atomic allocations | |
| [ 0.160875] console [pstore-1] enabled | |
| [ 0.160884] pstore: Registered ramoops as persistent store backend | |
| [ 0.160893] ramoops: attached 0xf0000@0x110000, ecc: 0/0 | |
| [ 0.228490] console [ttyFIQ0] enabled | |
| [ 0.229033] Registered fiq debugger ttyFIQ0 | |
| [ 0.243314] vbus_host: regulator get failed, ret=-517 | |
| [ 0.244021] vbus_typec: supplied by vcc5v0_sys | |
| [ 0.245089] vcc3v3_pcie: supplied by vcc5v0_sys | |
| [ 0.246311] iommu: Adding device ff650000.vpu_service to group 0 | |
| [ 0.246931] iommu: Adding device ff660000.rkvdec to group 1 | |
| [ 0.247534] iommu: Adding device ff8f0000.vop to group 2 | |
| [ 0.248110] iommu: Adding device ff900000.vop to group 3 | |
| [ 0.248672] iommu: Adding device ff910000.rkisp1 to group 4 | |
| [ 0.249643] rk_iommu ff650800.iommu: can't get sclk | |
| [ 0.250337] rk_iommu ff660480.iommu: can't get sclk | |
| [ 0.250958] rk_iommu ff8f3f00.iommu: can't get sclk | |
| [ 0.251561] rk_iommu ff903f00.iommu: can't get sclk | |
| [ 0.252150] rk_iommu ff914000.iommu: can't get sclk | |
| [ 0.252751] rk_iommu ff924000.iommu: can't get sclk | |
| [ 0.253551] SCSI subsystem initialized | |
| [ 0.254080] usbcore: registered new interface driver usbfs | |
| [ 0.254606] usbcore: registered new interface driver hub | |
| [ 0.255168] usbcore: registered new device driver usb | |
| [ 0.255683] media: Linux media interface: v0.10 | |
| [ 0.256133] Linux video capture interface: v2.00 | |
| [ 0.256626] pps_core: LinuxPPS API ver. 1 registered | |
| [ 0.257068] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome | |
| tti <[email protected]> | |
| [ 0.257899] PTP clock support registered | |
| [ 0.259336] Advanced Linux Sound Architecture Driver Initialized. | |
| [ 0.260997] rockchip-cpuinfo cpuinfo: Serial : 550f39de1ea9c0e8 | |
| [ 0.262007] clocksource: Switched to clocksource arch_sys_counter | |
| [ 0.317509] thermal thermal_zone1: power_allocator: sustainable_power will be | |
| estimated | |
| [ 0.318445] NET: Registered protocol family 2 | |
| [ 0.319303] TCP established hash table entries: 32768 (order: 6, 262144 bytes | |
| ) | |
| [ 0.320209] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes) | |
| [ 0.321619] TCP: Hash tables configured (established 32768 bind 32768) | |
| [ 0.322332] UDP hash table entries: 2048 (order: 5, 196608 bytes) | |
| [ 0.323065] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes) | |
| [ 0.324077] NET: Registered protocol family 1 | |
| [ 0.324768] RPC: Registered named UNIX socket transport module. | |
| [ 0.325308] RPC: Registered udp transport module. | |
| [ 0.325728] RPC: Registered tcp transport module. | |
| [ 0.326155] RPC: Registered tcp NFSv4.1 backchannel transport module. | |
| [ 0.327695] Trying to unpack rootfs image as initramfs... | |
| [ 1.266829] Freeing initrd memory: 19120K | |
| [ 1.267597] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counte | |
| rs available | |
| [ 1.268414] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counte | |
| rs available | |
| [ 1.272311] Initialise system trusted keyring | |
| [ 1.279804] VFS: Disk quotas dquot_6.6.0 | |
| [ 1.280331] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) | |
| [ 1.283210] NFS: Registering the id_resolver key type | |
| [ 1.283685] Key type id_resolver registered | |
| [ 1.284071] Key type id_legacy registered | |
| [ 1.284450] nfs4filelayout_init: NFSv4 File Layout Driver Registering... | |
| [ 1.289705] NET: Registered protocol family 38 | |
| [ 1.290131] Key type asymmetric registered | |
| [ 1.290498] Asymmetric key parser 'x509' registered | |
| [ 1.291107] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 | |
| 46) | |
| [ 1.291762] io scheduler noop registered | |
| [ 1.292128] io scheduler deadline registered | |
| [ 1.292736] io scheduler cfq registered (default) | |
| [ 1.294290] rockchip-usb2phy ff770000.syscon:usb2-phy@e450: failed to create | |
| phy | |
| [ 1.295396] rockchip-usb2phy ff770000.syscon:usb2-phy@e460: failed to create | |
| phy | |
| [ 1.301661] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found | |
| [ 1.302274] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found | |
| [ 1.302866] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found | |
| [ 1.303443] rockchip-pcie f8000000.pcie: missing "memory-region" property | |
| [ 1.304060] PCI host bridge /pcie@f8000000 ranges: | |
| [ 1.304503] MEM 0xfa000000..0xfbdfffff -> 0xfa000000 | |
| [ 1.304961] IO 0xfbe00000..0xfbefffff -> 0xfbe00000 | |
| [ 1.847070] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout! | |
| [ 1.847685] rockchip-pcie f8000000.pcie: deferred probe failed | |
| [ 1.848474] rockchip-pcie: probe of f8000000.pcie failed with error -110 | |
| [ 1.849919] Module initialized. | |
| [ 1.850670] rk-vcodec ff650000.vpu_service: no regulator for vcodec | |
| [ 1.851533] rk-vcodec ff650000.vpu_service: probe device | |
| [ 1.852260] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled | |
| [ 1.853386] rk-vcodec ff650000.vpu_service: could not find power_model node | |
| [ 1.854020] rk-vcodec ff650000.vpu_service: init success | |
| [ 1.854735] rk-vcodec ff660000.rkvdec: no regulator for vcodec | |
| [ 1.855705] rk-vcodec ff660000.rkvdec: probe device | |
| [ 1.856360] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled | |
| [ 1.857320] rk-vcodec ff660000.rkvdec: could not find power_model node | |
| [ 1.857903] rk-vcodec ff660000.rkvdec: init success | |
| [ 1.860051] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-2 | |
| 41330 | |
| [ 1.860727] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chan | |
| s-6 Num_Peri-12 Num_Events-12 | |
| [ 1.863035] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-2 | |
| 41330 | |
| [ 1.863710] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Cha | |
| ns-8 Num_Peri-20 Num_Events-16 | |
| [ 1.865573] rockchip-system-monitor rockchip-system-monitor: system monitor p | |
| robe | |
| [ 1.866952] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled | |
| [ 1.868182] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 35, base_baud = | |
| 1500000) is a 16550A | |
| [ 1.870034] [drm] Initialized drm 1.1.0 20060810 | |
| [ 1.874307] [drm] Rockchip DRM driver version: v1.0.1 | |
| [ 1.876764] mali ff9a0000.gpu: Failed to get regulator | |
| [ 1.877232] mali ff9a0000.gpu: Power control initialization failed | |
| [ 1.878136] Unable to detect cache hierarchy for CPU 0 | |
| [ 1.879333] brd: module loaded | |
| [ 1.884787] loop: module loaded | |
| [ 1.885634] zram: Added device: zram0 | |
| [ 1.886263] lkdtm: No crash points registered, enable through debugfs | |
| [ 1.889027] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input). | |
| [ 1.889657] rk_gmac-dwmac fe300000.ethernet: TX delay(0x2a). | |
| [ 1.890174] rk_gmac-dwmac fe300000.ethernet: RX delay(0x21). | |
| [ 1.890691] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no). | |
| [ 1.891418] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed | |
| [ 1.892043] rk_gmac-dwmac fe300000.ethernet: clock input from PHY | |
| [ 1.897595] rk_gmac-dwmac fe300000.ethernet: init for RGMII | |
| [ 1.898221] stmmac - user ID: 0x10, Synopsys ID: 0x35 | |
| [ 1.898674] Ring mode enabled | |
| [ 1.898956] DMA HW capability register supported | |
| [ 1.899372] Normal descriptors | |
| [ 1.899680] RX Checksum Offload Engine supported (type 2) | |
| [ 1.900174] TX Checksum insertion supported | |
| [ 1.900557] Wake-Up On Lan supported | |
| [ 1.900917] Enable RX Mitigation via HW Watchdog Timer | |
| [ 2.039176] libphy: stmmac: probed | |
| [ 2.039492] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active | |
| [ 2.040070] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01) | |
| [ 2.042057] Rockchip WiFi SYS interface (V1.00) ... | |
| [ 2.042640] usbcore: registered new interface driver asix | |
| [ 2.043196] usbcore: registered new interface driver cdc_ether | |
| [ 2.043764] usbcore: registered new interface driver rndis_host | |
| [ 2.044388] usbcore: registered new interface driver cdc_ncm | |
| [ 2.046893] rockchip-dwc3 usb0: failed to get drvdata dwc3 | |
| [ 2.048975] rockchip-dwc3 usb1: failed to get drvdata dwc3 | |
| [ 2.050572] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
| [ 2.051240] ehci-pci: EHCI PCI platform driver | |
| [ 2.051705] ehci-platform: EHCI generic platform driver | |
| [ 2.053104] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
| [ 2.053672] ohci-platform: OHCI generic platform driver | |
| [ 2.055236] usbcore: registered new interface driver usb-storage | |
| [ 2.057313] i2c /dev entries driver | |
| [ 2.058854] rk808 0-0020: Pmic Chip id: 0x8090 | |
| [ 2.059589] rk808 0-0020: source: on=0x40, off=0x00 | |
| [ 2.060811] rk808 0-0020: support dcdc3 fb mode:-22, -377421824 | |
| [ 2.061601] rk808 0-0020: support pmic reset mode:0,0 | |
| [ 2.064955] rk808-regulator rk808-regulator: there is no dvs0 gpio | |
| [ 2.065604] rk808-regulator rk808-regulator: there is no dvs1 gpio | |
| [ 2.066257] DCDC_REG1: supplied by vcc5v0_sys | |
| [ 2.068151] DCDC_REG2: supplied by vcc5v0_sys | |
| [ 2.070131] DCDC_REG3: supplied by vcc5v0_sys | |
| [ 2.071819] DCDC_REG4: supplied by vcc5v0_sys | |
| [ 2.073523] DCDC_REG5: supplied by vcc5v0_sys | |
| [ 2.075033] LDO_REG1: supplied by vcc_buck5 | |
| [ 2.077210] LDO_REG2: supplied by vcc_buck5 | |
| [ 2.079387] LDO_REG3: supplied by vcc_buck5 | |
| [ 2.081564] LDO_REG4: supplied by vcc_buck5 | |
| [ 2.083725] LDO_REG5: supplied by vcc_buck5 | |
| [ 2.084570] vcc_mipi: Bringing 1500000uV into 3000000-3000000uV | |
| [ 2.087141] LDO_REG6: supplied by vcc_buck5 | |
| [ 2.089362] LDO_REG7: supplied by vcc5v0_sys | |
| [ 2.091432] LDO_REG8: supplied by vcc5v0_sys | |
| [ 2.093627] LDO_REG9: supplied by vcc5v0_sys | |
| [ 2.095719] SWITCH_REG1: supplied by vcc5v0_sys | |
| [ 2.096511] vbus_host: supplied by vcc5v0_usb2.0 | |
| [ 2.097425] SWITCH_REG2: supplied by vcc3v3_sys | |
| [ 2.099023] rk817-battery rk817-battery: Failed to find matching dt id | |
| [ 2.099767] rk817-charger rk817-charger: Failed to find matching dt id | |
| [ 2.102488] input: rk8xx_pwrkey as /devices/platform/ff3c0000.i2c/i2c-0/0-002 | |
| 0/input/input0 | |
| [ 2.106906] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0 | |
| [ 2.109422] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! | |
| [ 2.110097] fan53555-reg: supplied by vcc5v0_sys | |
| [ 2.112824] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! | |
| [ 2.113493] fan53555-reg: supplied by vcc5v0_sys | |
| [ 2.115992] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff80091b | |
| e000 | |
| [ 2.117972] IR NEC protocol handler initialized | |
| [ 2.119196] rkisp1 ff910000.rkisp1: rkisp1 driver version: v00.01.05 | |
| [ 2.119785] rkisp1 ff910000.rkisp1: Missing rockchip,grf property | |
| [ 2.121894] usbcore: registered new interface driver npu_acm | |
| [ 2.122468] usbcore: registered new interface driver uvcvideo | |
| [ 2.122978] USB Video Class driver (1.1.1) | |
| [ 2.126656] Boot mode: normal | |
| [ 2.127965] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, tem | |
| perature=2147483647 | |
| [ 2.128925] rockchip-thermal ff260000.tsadc: tsadc is probed successfully! | |
| [ 2.130116] dw_wdt ff848000.watchdog: Should better to setup a 'resets' prope | |
| rty in dt, that must been named with reset | |
| [ 2.131742] cpu cpu0: bin=2 | |
| [ 2.132076] cpu cpu0: leakage=0 | |
| [ 2.145146] cpu cpu0: temp=35625, pvtm=136773 (137463 + -690) | |
| [ 2.146653] cpu cpu0: pvtm-volt-sel=0 | |
| [ 2.147057] cpu cpu0: bin-scale=46 | |
| [ 2.147368] cpu cpu0: bin-volt-sel=20 | |
| [ 2.147979] cpu cpu4: bin=2 | |
| [ 2.148336] cpu cpu4: leakage=0 | |
| [ 2.160805] cpu cpu4: temp=35625, pvtm=148833 (149259 + -426) | |
| [ 2.161480] cpu cpu4: pvtm-volt-sel=0 | |
| [ 2.161852] cpu cpu4: bin-scale=30 | |
| [ 2.162201] cpu cpu4: bin-volt-sel=20 | |
| [ 2.163922] cpu cpu0: avs=0 | |
| [ 2.164218] cpu cpu0: scale_rate=1008000000 | |
| [ 2.164845] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table= | |
| 0 | |
| [ 2.166329] cpu cpu0: failed to find power_model node | |
| [ 2.167784] cpu cpu4: avs=0 | |
| [ 2.168073] cpu cpu4: scale_rate=1512000000 | |
| [ 2.168696] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table= | |
| 0 | |
| [ 2.170500] cpu cpu4: failed to find power_model node | |
| [ 2.171803] sdhci: Secure Digital Host Controller Interface driver | |
| [ 2.172386] sdhci: Copyright(c) Pierre Ossman | |
| [ 2.172778] Synopsys Designware Multimedia Card Interface Driver | |
| [ 2.174197] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode | |
| . | |
| [ 2.175167] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller. | |
| [ 2.175786] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a | |
| [ 2.176413] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit | |
| host data width,256 deep fifo | |
| [ 2.177415] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found | |
| [ 2.177964] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found | |
| [ 2.179662] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode | |
| . | |
| [ 2.180348] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller. | |
| [ 2.180958] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a | |
| [ 2.181511] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit | |
| host data width,256 deep fifo | |
| [ 2.182711] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found | |
| [ 2.184574] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 | |
| done | |
| [ 2.185647] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 | |
| done | |
| [ 2.199044] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, | |
| actual 400000HZ div = 0) | |
| [ 2.212591] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized | |
| [ 2.213468] sdhci-pltfm: SDHCI platform and OF driver helper | |
| [ 2.215705] sdhci-arasan fe330000.sdhci: No vmmc regulator found | |
| [ 2.216246] sdhci-arasan fe330000.sdhci: No vqmmc regulator found | |
| [ 2.247223] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using A | |
| DMA | |
| [ 2.247428] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000 | |
| Hz, actual 50000000HZ div = 0) | |
| [ 2.247779] mmc0: new high speed SDXC card at address 59b4 | |
| [ 2.250069] mmcblk0: mmc0:59b4 SK64G 59.4 GiB | |
| [ 2.250917] ledtrig-cpu: registered to indicate activity on CPUs | |
| [ 2.251593] hidraw: raw HID events driver (C) Jiri Kosina | |
| [ 2.252447] usbcore: registered new interface driver usbhid | |
| [ 2.252949] usbhid: USB HID core driver | |
| [ 2.254208] rockchip-dmc dmc: Cannot get the regulator "center" | |
| [ 2.255421] extcon-pd-virtual virtual-pd0: vpd_extcon_probe: 376 start | |
| [ 2.256985] extcon-pd-virtual virtual-pd0: vpd_extcon_probe: 507 success | |
| [ 2.260929] GPT:Primary header thinks Alt. header is not at the end of the di | |
| sk. | |
| [ 2.261038] usbcore: registered new interface driver snd-usb-audio | |
| [ 2.262202] GPT:7812499 != 124669951 | |
| [ 2.262526] GPT:Alternate GPT header not at the end of the disk. | |
| [ 2.263062] GPT:7812499 != 124669951 | |
| [ 2.263386] GPT: Use GNU Parted to correct GPT errors. | |
| [ 2.263867] mmcblk0: p1 p2 p3 p4 p5 | |
| [ 2.265802] Initializing XFRM netlink socket | |
| [ 2.266217] NET: Registered protocol family 17 | |
| [ 2.266670] [WLAN_RFKILL]: Enter rfkill_wlan_init | |
| [ 2.267259] [WLAN_RFKILL]: Enter rfkill_wlan_probe | |
| [ 2.267708] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6256 | |
| [ 2.268327] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control. | |
| [ 2.268960] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gp | |
| io. | |
| [ 2.269680] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wa | |
| ke_irq = 3, flags = 0. | |
| [ 2.270489] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found | |
| ! | |
| [ 2.271140] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio | |
| [ 2.271604] [WLAN_RFKILL]: Exit rfkill_wlan_probe | |
| [ 2.272068] [BT_RFKILL]: Enter rfkill_rk_init | |
| [ 2.272765] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_ | |
| gpios = 83. | |
| [ 2.273521] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_ | |
| gpio = 9. | |
| [ 2.274249] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_g | |
| pio = 91. | |
| [ 2.274970] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_h | |
| ost_irq = 4. | |
| [ 2.276064] [BT_RFKILL]: Request irq for bt wakeup host | |
| [ 2.276571] [BT_RFKILL]: ** disable irq | |
| [ 2.277075] [BT_RFKILL]: bt_default device registered. | |
| [ 2.277597] Key type dns_resolver registered | |
| [ 2.278659] Registered cp15_barrier emulation handler | |
| [ 2.279217] Registered setend emulation handler | |
| [ 2.281642] registered taskstats version 1 | |
| [ 2.282067] Loading compiled-in X.509 certificates | |
| [ 2.283463] rga2: Driver loaded successfully ver:3.2.18218 | |
| [ 2.284118] rga2: Module initialized. | |
| [ 2.285899] phy phy-ff770000.syscon:[email protected]: Failed to get VBUS suppl | |
| y regulator | |
| [ 2.288042] phy phy-ff770000.syscon:[email protected]: Failed to get VBUS suppl | |
| y regulator | |
| [ 2.290568] rockchip-drm display-subsystem: defer getting devfreq | |
| [ 2.291475] rockchip-vop ff900000.vop: missing rockchip,grf property | |
| [ 2.292397] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8 | |
| 008ab7368) | |
| [ 2.293161] rockchip-vop ff8f0000.vop: missing rockchip,grf property | |
| [ 2.293944] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8 | |
| 008ab7368) | |
| [ 2.295294] i2c i2c-9: of_i2c: modalias failure on /hdmi@ff940000/ports | |
| [ 2.295914] dwhdmi-rockchip ff940000.hdmi: registered DesignWare HDMI I2C bus | |
| driver | |
| [ 2.296749] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a | |
| with HDCP (DWC HDMI 2.0 TX PHY) | |
| [ 2.300034] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff | |
| 8008aab878) | |
| [ 2.302240] i2c i2c-10: of_i2c: modalias failure on /dp@fec00000/ports | |
| [ 2.303935] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff80 | |
| 08aac8f0) | |
| [ 2.304707] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). | |
| [ 2.305347] [drm] No driver support for vblank timestamp query. | |
| [ 2.306188] rockchip-drm display-subsystem: failed to parse loader memory | |
| [ 2.306843] rockchip-drm display-subsystem: No connectors reported connected | |
| with modes | |
| [ 2.307632] [drm] Cannot find any crtc or sizes - going 1024x768 | |
| [ 2.323895] Console: switching to colour frame buffer device 128x48 | |
| [ 2.336146] rockchip-drm display-subsystem: fb0: frame buffer device | |
| [ 2.343044] mali ff9a0000.gpu: bin=2 | |
| [ 2.343417] mali ff9a0000.gpu: leakage=0 | |
| [ 2.356987] mali ff9a0000.gpu: temp=36250, pvtm=116120 (116350 + -230) | |
| [ 2.359618] mali ff9a0000.gpu: pvtm-volt-sel=0 | |
| [ 2.360107] mali ff9a0000.gpu: bin-scale=61 | |
| [ 2.360485] mali ff9a0000.gpu: bin-volt-sel=20 | |
| [ 2.361570] mali ff9a0000.gpu: avs=0 | |
| [ 2.361921] mali ff9a0000.gpu: scale_rate=600000000 | |
| [ 2.363085] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0 | |
| [ 2.364041] mali ff9a0000.gpu: Protected mode not available | |
| [ 2.365204] mali ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 | |
| h_table=0 | |
| [ 2.365987] mali ff9a0000.gpu: Using configured power model mali-simple-power | |
| -model, and fallback mali-simple-power-model | |
| [ 2.367162] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfr | |
| eq.c; [Line] : 423; [Func] : kbase_devfreq_init(); success initing power_model_s | |
| imple. | |
| [ 2.369463] mali ff9a0000.gpu: Probed as mali0 | |
| [ 2.376137] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller | |
| [ 2.376647] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus nu | |
| mber 1 | |
| [ 2.377593] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 | |
| quirks 0x06030010 | |
| [ 2.380471] xhci-hcd xhci-hcd.9.auto: irq 225, io mem 0xfe800000 | |
| [ 2.381285] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 | |
| [ 2.381886] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.382543] usb usb1: Product: xHCI Host Controller | |
| [ 2.382984] usb usb1: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 xhci-hcd | |
| [ 2.383728] usb usb1: SerialNumber: xhci-hcd.9.auto | |
| [ 2.384750] hub 1-0:1.0: USB hub found | |
| [ 2.385161] hub 1-0:1.0: 1 port detected | |
| [ 2.385885] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller | |
| [ 2.386407] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus nu | |
| mber 2 | |
| [ 2.387176] usb usb2: We don't know the algorithms for LPM for this host, dis | |
| abling LPM. | |
| [ 2.387990] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 | |
| [ 2.388604] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.389258] usb usb2: Product: xHCI Host Controller | |
| [ 2.389699] usb usb2: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 xhci-hcd | |
| [ 2.390443] usb usb2: SerialNumber: xhci-hcd.9.auto | |
| [ 2.391414] hub 2-0:1.0: USB hub found | |
| [ 2.391775] hub 2-0:1.0: 1 port detected | |
| [ 2.392707] xhci-hcd xhci-hcd.9.auto: remove, state 1 | |
| [ 2.393200] usb usb2: USB disconnect, device number 1 | |
| [ 2.394129] xhci-hcd xhci-hcd.9.auto: USB bus 2 deregistered | |
| [ 2.394650] xhci-hcd xhci-hcd.9.auto: remove, state 1 | |
| [ 2.395157] usb usb1: USB disconnect, device number 1 | |
| [ 2.396640] xhci-hcd xhci-hcd.9.auto: USB bus 1 deregistered | |
| [ 2.397627] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller | |
| [ 2.398166] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus n | |
| umber 1 | |
| [ 2.399110] xhci-hcd xhci-hcd.10.auto: hcc params 0x0220fe64 hci version 0x11 | |
| 0 quirks 0x06030010 | |
| [ 2.399926] xhci-hcd xhci-hcd.10.auto: irq 226, io mem 0xfe900000 | |
| [ 2.400728] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 | |
| [ 2.401350] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.401985] usb usb1: Product: xHCI Host Controller | |
| [ 2.402438] usb usb1: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 xhci-hcd | |
| [ 2.403183] usb usb1: SerialNumber: xhci-hcd.10.auto | |
| [ 2.404267] hub 1-0:1.0: USB hub found | |
| [ 2.404633] hub 1-0:1.0: 1 port detected | |
| [ 2.405327] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller | |
| [ 2.405833] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus n | |
| umber 2 | |
| [ 2.406596] usb usb2: We don't know the algorithms for LPM for this host, dis | |
| abling LPM. | |
| [ 2.407423] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 | |
| [ 2.408034] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.408669] usb usb2: Product: xHCI Host Controller | |
| [ 2.409119] usb usb2: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 xhci-hcd | |
| [ 2.409855] usb usb2: SerialNumber: xhci-hcd.10.auto | |
| [ 2.410784] hub 2-0:1.0: USB hub found | |
| [ 2.411187] hub 2-0:1.0: 1 port detected | |
| [ 2.412930] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller | |
| [ 2.413510] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus nu | |
| mber 3 | |
| [ 2.414507] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 | |
| quirks 0x06030010 | |
| [ 2.414804] ehci-platform fe380000.usb: EHCI Host Controller | |
| [ 2.414828] ehci-platform fe380000.usb: new USB bus registered, assigned bus | |
| number 4 | |
| [ 2.415047] ehci-platform fe380000.usb: irq 28, io mem 0xfe380000 | |
| [ 2.417062] xhci-hcd xhci-hcd.9.auto: irq 225, io mem 0xfe800000 | |
| [ 2.417846] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 | |
| [ 2.418502] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.419164] usb usb3: Product: xHCI Host Controller | |
| [ 2.419602] usb usb3: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 xhci-hcd | |
| [ 2.420353] usb usb3: SerialNumber: xhci-hcd.9.auto | |
| [ 2.421097] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00 | |
| [ 2.421512] hub 3-0:1.0: USB hub found | |
| [ 2.421547] hub 3-0:1.0: 1 port detected | |
| [ 2.421907] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller | |
| [ 2.421922] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus nu | |
| mber 5 | |
| [ 2.422053] usb usb5: We don't know the algorithms for LPM for this host, dis | |
| abling LPM. | |
| [ 2.422176] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 | |
| [ 2.422183] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.422189] usb usb5: Product: xHCI Host Controller | |
| [ 2.422195] usb usb5: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 xhci-hcd | |
| [ 2.422200] usb usb5: SerialNumber: xhci-hcd.9.auto | |
| [ 2.422926] hub 5-0:1.0: USB hub found | |
| [ 2.422966] hub 5-0:1.0: 1 port detected | |
| [ 2.423344] rockchip-dwc3 usb0: USB HOST connected | |
| [ 2.428496] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 | |
| [ 2.429143] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.429778] usb usb4: Product: EHCI Host Controller | |
| [ 2.430231] usb usb4: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 ehci_hcd | |
| [ 2.430967] usb usb4: SerialNumber: fe380000.usb | |
| [ 2.431985] hub 4-0:1.0: USB hub found | |
| [ 2.432395] hub 4-0:1.0: 1 port detected | |
| [ 2.435751] ehci-platform fe3c0000.usb: EHCI Host Controller | |
| [ 2.436293] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus | |
| number 6 | |
| [ 2.437245] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000 | |
| [ 2.443191] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00 | |
| [ 2.444055] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002 | |
| [ 2.444664] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.445347] usb usb6: Product: EHCI Host Controller | |
| [ 2.445795] usb usb6: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 ehci_hcd | |
| [ 2.446549] usb usb6: SerialNumber: fe3c0000.usb | |
| [ 2.447864] hub 6-0:1.0: USB hub found | |
| [ 2.448240] hub 6-0:1.0: 1 port detected | |
| [ 2.449624] ohci-platform fe3a0000.usb: Generic Platform OHCI controller | |
| [ 2.450251] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus | |
| number 7 | |
| [ 2.451138] ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000 | |
| [ 2.506425] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 | |
| [ 2.507052] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.507697] usb usb7: Product: Generic Platform OHCI controller | |
| [ 2.508238] usb usb7: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 ohci_hcd | |
| [ 2.508974] usb usb7: SerialNumber: fe3a0000.usb | |
| [ 2.510104] hub 7-0:1.0: USB hub found | |
| [ 2.510470] hub 7-0:1.0: 1 port detected | |
| [ 2.511886] ohci-platform fe3e0000.usb: Generic Platform OHCI controller | |
| [ 2.512520] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus | |
| number 8 | |
| [ 2.513406] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000 | |
| [ 2.568469] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 | |
| [ 2.569096] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber= | |
| 1 | |
| [ 2.569741] usb usb8: Product: Generic Platform OHCI controller | |
| [ 2.570283] usb usb8: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4 | |
| 9cc40 ohci_hcd | |
| [ 2.571028] usb usb8: SerialNumber: fe3e0000.usb | |
| [ 2.572235] hub 8-0:1.0: USB hub found | |
| [ 2.572601] hub 8-0:1.0: 1 port detected | |
| [ 2.574567] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode | |
| . | |
| [ 2.575316] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller. | |
| [ 2.575922] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a | |
| [ 2.576470] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit | |
| host data width,256 deep fifo | |
| [ 2.577454] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found | |
| [ 2.578019] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found | |
| [ 2.578985] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq | |
| [ 2.592500] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, | |
| actual 400000HZ div = 0) | |
| [ 2.606308] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized | |
| [ 2.613646] asoc-simple-card rk809-sound: rk817-hifi <-> ff880000.i2s mapping | |
| ok | |
| [ 2.614332] asoc-simple-card rk809-sound: ASoC: no source widget found for MI | |
| CBIAS1 | |
| [ 2.615023] asoc-simple-card rk809-sound: ASoC: Failed to add route MICBIAS1 | |
| -> direct -> Mic Jack | |
| [ 2.615807] asoc-simple-card rk809-sound: ASoC: no sink widget found for IN1P | |
| [ 2.616448] asoc-simple-card rk809-sound: ASoC: Failed to add route Mic Jack | |
| -> direct -> IN1P | |
| [ 2.617215] asoc-simple-card rk809-sound: ASoC: no source widget found for HP | |
| OL | |
| [ 2.617861] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOL -> d | |
| irect -> Headphone Jack | |
| [ 2.618672] asoc-simple-card rk809-sound: ASoC: no source widget found for HP | |
| OR | |
| [ 2.619325] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOR -> d | |
| irect -> Headphone Jack | |
| [ 2.621247] rk-hdmi-dp-sound hdmi-dp-sound: control 3:0:0:ELD:0 is already pr | |
| esent | |
| [ 2.621920] hdmi-audio-codec hdmi-audio-codec.8.auto: ASoC: Failed to add ELD | |
| : -16 | |
| [ 2.623050] rk-hdmi-dp-sound hdmi-dp-sound: multicodec <-> ff8a0000.i2s mappi | |
| ng ok | |
| [ 2.623752] hdmi-audio-codec hdmi-audio-codec.8.auto: ASoC: Failed to create | |
| Playback debugfs file | |
| [ 2.625175] ======================================================= | |
| [ 2.625731] ==== Launching Wi-Fi driver! (Powered by Rockchip) ==== | |
| [ 2.626299] ======================================================= | |
| [ 2.626853] WiFi driver (Powered by Rockchip,Ver 5.10.WFD.OOB.64bit) init. | |
| [ 2.627715] dhd_module_init in | |
| [ 2.628225] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter | |
| [ 2.628726] dhd_wlan_init_plat_data, irq = 67Power-up adapter 'DHD generic ad | |
| apter' | |
| [ 2.629485] wifi_platform_set_power = 1 | |
| [ 2.629506] rk808-rtc rk808-rtc: setting system clock to 2017-08-04 09:00:15 | |
| UTC (1501837215) | |
| [ 2.630593] [WLAN_RFKILL]: rockchip_wifi_power: 1 | |
| [ 2.631018] [WLAN_RFKILL]: wifi turn on power. -1 | |
| [ 2.644899] rockchip_headset_probe() headset have hook adc mode | |
| [ 2.645656] input: rk-headset as /devices/platform/rk-headset/input/input1 | |
| [ 2.647968] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux | |
| .c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this m | |
| ali_ko is '', rk_ko_ver is '5', built at '21:30:56', on 'Nov 4 2022'. | |
| [ 2.650299] Mali: Mali device driver loaded | |
| [ 2.650920] rkisp1 ff910000.rkisp1: clear unready subdev num: 1 | |
| [ 2.652228] rockchip-mipi-dphy-rx: No link between dphy and sensor | |
| [ 2.652781] rockchip-mipi-dphy-rx: No link between dphy and sensor | |
| [ 2.653347] rkisp1: update sensor failed | |
| [ 2.653437] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) | |
| [ 2.654610] ALSA device list: | |
| [ 2.654879] #0: rockchip,rk809-codec | |
| [ 2.654991] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) | |
| [ 2.655707] #1: rk-hdmi-dp-sound | |
| [ 2.656566] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) | |
| [ 2.656578] Freeing unused kernel memory: 1024K | |
| [ 2.660300] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) | |
| [ 2.661722] mmc2: queuing unknown CIS tuple 0x81 (1 bytes) | |
| Loading, please wait... | |
| Starting version 247.3-7+deb11u1 | |
| [ 2.717607] mmc_host mmc2: Bus speed (slot 0) = 200000000Hz (slot req 2000000 | |
| 00Hz, actual 200000000HZ div = 0) | |
| [ 2.798032] headset_interrupt:get pin level again,pin=2,i=0 | |
| [ 2.832087] wifi_platform_bus_enumerate device present 1 | |
| [ 2.832569] mmc2:mmc host rescan start! |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment