tmelz · March 14, 2022 19:58
diff --git a/samoklava.yaml b/samoklava.yaml
 units:
  kx: cx
  ky: cy
  px: 2
  py: 2
 points:
  key:
    footprints:
      choc_hotswap:
        type: choc
        params:
          hotswap: true
          reverse: true
          keycaps: true
        nets:
          # from: P1
          # to: P2
          from: =colrow
          to: =column_net
      diode:
        type: diode
        nets:
          # from: P3
          # to: P4
          from: =colrow
          to: =row_net
        anchor:
          shift: [0, -5]
  zones:
    matrix:
      # anchor:
      #   rotate: 5
      key.padding: ky
      columns:
        pinky:
          stagger: 0 ky
          spread: kx
          key:
            column_net: P20
        ring:
          stagger: 0.7 ky
          spread: kx
          key:
            column_net: P19
        middle:
          stagger: 0.2 ky
          spread: kx
          key:
            column_net: P18
        index:
          stagger: -0.2 ky
          spread: kx
          key:
            column_net: P15
        inner:
          stagger: -0.1 ky
          spread: kx
          key:
            column_net: P14
      rows:
        bottom:
          row_net: P6
        home:
          row_net: P5
        top:
          row_net: P4
    thumbfan:
      anchor:
        ref: matrix_inner_bottom
        shift: [-1.5 kx, -1 ky]
      columns:
        near:
          spread: kx
          rotate: -15
          origin: [-0.5 kx, -0.5 ky]
          key:
            column_net: P18
        home:
          spread: kx
          rotate: -15
          origin: [-0.5 kx, -0.5 ky]
          key:
            column_net: P15
        far:
          spread: kx
          rotate: -15
          origin: [-0.5 kx, -0.5 ky]
          key:
            column_net: P14
      rows:
        thumb:
          row_net: P7
 outlines:
  # board dimensions according to JLCPCB: 122.28 mm x 101.05 mm
  exports:
    raw:
      - type: keys
        side: left
        size: [kx + px, ky + py]
        corner: px
    thumbfan_glue:
      - type: polygon
        points:
          - ref: matrix_inner_bottom
            shift: [0.5 kx + 0.5px, -0.5 ky + 0.5 py]
          - ref: thumbfan_far_thumb
            shift: [0.5 kx - 0.5px, 0.5 ky + 0.5 py]
          - ref: thumbfan_far_thumb
            shift: [0.5 kx - 0.5px, -0.5 ky - 0.5 py]
          - ref: thumbfan_near_thumb
            shift: [-0.5 kx + 0.5 px, -0.5 ky - 0.5 py]
          - ref: matrix_pinky_bottom
            shift: [0.5 kx - 0.5 py, -0.5 ky - 0.5 py]
          - ref: matrix_pinky_home
          - ref: matrix_inner_home
    patch_outer:
      - type: polygon
        points:
          - ref: matrix_ring_top
          - ref: matrix_ring_bottom
          - ref: matrix_pinky_bottom
            shift: [-0.5 (kx + px), 0]
          - ref: matrix_pinky_top
            shift: [-0.5 (kx + px), 0]
    patch_inner:
      - type: polygon
        points:
          - ref: matrix_inner_top
            shift: [0.5 (kx + px), 0]
          - ref: matrix_inner_bottom
            shift: [0.5 (kx + px), 0]
          - ref: matrix_index_bottom
          - ref: matrix_index_top
    controller_area:
      main:
        type: rectangle
        anchor:
          ref:
            - matrix_inner_top
          shift: [0 kx, -4.05 ky]
        size: [32, 76.5]
        corner: px
    switches:
      main:
        type: keys
        side: left
        size: 14
        bound: false
    keycaps:
      main:
        type: keys
        side: left
        size: [kx, ky]
        bound: false
        corner: 1
    keywell:
      main:
        type: outline
        name: raw
      patch_inner:
        type: outline
        name: patch_inner
        operation: add
      patch_outer:
        type: outline
        name: patch_outer
        operation: add
      thumbfan_glue:
        type: outline
        name: thumbfan_glue
        operation: add
    base_outline:
      main:
        type: outline
        name: keywell
      controller:
        type: outline
        name: controller_area
        operation: add
    screw_holes:
      top_left:
        type: circle
        anchor:
          - ref: matrix_ring_home
            shift: [-0.5 kx, 0 ky]
        radius: 1.05
      bottom_left:
        type: circle
        anchor:
          - ref: matrix_pinky_bottom
            shift: [0.5 kx, 0]
        radius: 1.05
      top_right:
        type: circle
        anchor:
          - ref: matrix_inner_top
            shift: [-0.5 kx, 0]
        radius: 1.05
      palm:
        type: circle
        anchor:
          - ref: matrix_index_bottom
            shift: [0, -1.06 ky]
        radius: 1.05
      thumb:
        type: circle
        anchor:
          - ref: thumbfan_far_thumb
            shift: [-0.55 kx, 0]
        radius: 1.05
    mounting_holes:
      $extends: outlines.exports.screw_holes
      top_left:
        radius: 2.05
      bottom_left:
        radius: 2.05
      top_right:
        radius: 2.05
      palm:
        radius: 2.05
      thumb:
        radius: 2.05
    bottom_outline:
      main:
        type: outline
        name: base_outline
      screw_holes:
        type: outline
        # TODO use footprints with pad + via reinforcement as mounting holes
        name: screw_holes
        operation: subtract
    plate:
      main:
        type: outline
        name: keywell
      switches:
        type: outline
        name: switches
        operation: subtract
      mounting_holes:
        type: outline
        # TODO use footprints with pad + via reinforcement as mounting holes
        name: screw_holes
        operation: subtract
    pcb:
      main:
        type: outline
        name: base_outline
      mounting_holes:
        type: outline
        # TODO use plated through hole footprints as mounting holes
        name: mounting_holes
        operation: subtract
 pcbs:
  top_plate:
    # include JLCJLCJLCJLC text somewhere
    include_keys: false
    outlines:
      edge:
        outline: plate
        layer: Edge.Cuts
    footprints:
      jlc_order_number:
        type: text
        anchor:
          ref:
            - matrix_ring_home
          shift: [-0.25 kx, 0.5 ky]
        params:
          text: "JLCJLCJLCJLC"
          justify: left
  bottom_plate:
    include_keys: false
    outlines:
      edge:
        outline: bottom_outline
        layer: Edge.Cuts
  board:
    outlines:
      edge:
        outline: pcb
        layer: Edge.Cuts
        # TODO there's a way to add stuff to the silkscreen layer
    footprints:
      mcu_l:
        type: promicro
        params:
          orientation: up
          batteryPins: true
        anchor:
          ref:
            - matrix_inner_top
          shift: [20, -11]
          rotate: 270
      mcu_r:
        type: promicro
        params:
          orientation: down
          batteryPins: true
        anchor:
          ref:
            - matrix_inner_top
          shift: [22.5, -12.25]
          rotate: 270
      pad_plus:
        type: pad
        anchor:
          ref:
            - matrix_inner_top
          shift: [23, -18]
          rotate: 0
        params:
          front: true
          back: true
          width: 1.5
          height: 1.5
          text: "B+"
        nets:
          net: Braw
      pad_minus:
        type: pad
        anchor:
          ref:
            - matrix_inner_top
          shift: [23, -15]
          rotate: 0
        params:
          front: true
          back: true
          width: 1.5
          height: 1.5
          text: "B-"
        nets:
          net: Bminus
      trrs_l:
        type: trrs
        anchor:
          ref:
            - matrix_inner_bottom
          shift: [32, -15]
          rotate: 270
        params:
          reverse: false
          symmetric: false
        # The naming of the nets on this footprint is different from the Corne schematics.
        nets:
          A: ""
          B: VCC
          C: GND
          D: P0
      trrs_r:
        type: trrs
        anchor:
          ref:
            - matrix_inner_bottom
          shift: [32, -13]
          rotate: 270
        params:
          reverse: true
          symmetric: false
        # The naming of the nets on this footprint is different from the Corne schematics.
        nets:
          A: ""
          B: VCC
          C: GND
          D: P0
      jumper_l:
        type: jumper
        anchor:
          ref:
            - matrix_inner_bottom
          shift: [23.5, 0]
          rotate: 270
        params:
          side: B
        nets:
          from: Braw
          to: Bplus
      jumper_r:
        type: jumper
        anchor:
          ref:
            - matrix_inner_bottom
          shift: [23.5, 0]
          rotate: 270
        params:
          side: F
        nets:
          from: Braw
          to: Bplus
      slider_l:
        type: slider
        anchor:
          ref:
            - matrix_inner_bottom
          shift: [30, 0]
          rotate: 270
        params:
          side: F
        nets:
          from: Braw
          to: Bplus
      slider_r:
        type: slider
        anchor:
          ref:
            - matrix_inner_bottom
          shift: [30, 0]
          rotate: 270
        params:
          side: B
        nets:
          from: Braw
          to: Bplus
      reset:
        type: button
        anchor:
          ref:
            - matrix_inner_bottom
          shift: [17, 0]
          rotate: 270
        params:
          variant: 2_pin_th
        nets:
          from: GND
          to: RST
      info_l:
        type: text
        anchor:
          ref:
            - matrix_pinky_bottom
          shift: [0.75 kx, 0]
        params:
          text: "samoklava v0.1\\nby soundmonster"
          justify: left
      info_r:
        type: text
        anchor:
          ref:
            - matrix_pinky_bottom
          shift: [0.75 kx, 0]
        params:
          layer: B.SilkS
          text: "samoklava v0.1\\nby soundmonster"
          justify: right mirror
	units:
	kx: cx
	ky: cy
	px: 2
	py: 2
	points:
	key:
	footprints:
	choc_hotswap:
	type: choc
	params:
	hotswap: true
	reverse: true
	keycaps: true
	nets:
	# from: P1
	# to: P2
	from: =colrow
	to: =column_net
	diode:
	type: diode
	nets:
	# from: P3
	# to: P4
	from: =colrow
	to: =row_net
	anchor:
	shift: [0, -5]
	zones:
	matrix:
	# anchor:
	# rotate: 5
	key.padding: ky
	columns:
	pinky:
	stagger: 0 ky
	spread: kx
	key:
	column_net: P20
	ring:
	stagger: 0.7 ky
	spread: kx
	key:
	column_net: P19
	middle:
	stagger: 0.2 ky
	spread: kx
	key:
	column_net: P18
	index:
	stagger: -0.2 ky
	spread: kx
	key:
	column_net: P15
	inner:
	stagger: -0.1 ky
	spread: kx
	key:
	column_net: P14
	rows:
	bottom:
	row_net: P6
	home:
	row_net: P5
	top:
	row_net: P4
	thumbfan:
	anchor:
	ref: matrix_inner_bottom
	shift: [-1.5 kx, -1 ky]
	columns:
	near:
	spread: kx
	rotate: -15
	origin: [-0.5 kx, -0.5 ky]
	key:
	column_net: P18
	home:
	spread: kx
	rotate: -15
	origin: [-0.5 kx, -0.5 ky]
	key:
	column_net: P15
	far:
	spread: kx
	rotate: -15
	origin: [-0.5 kx, -0.5 ky]
	key:
	column_net: P14
	rows:
	thumb:
	row_net: P7
	outlines:
	# board dimensions according to JLCPCB: 122.28 mm x 101.05 mm
	exports:
	raw:
	- type: keys
	side: left
	size: [kx + px, ky + py]
	corner: px
	thumbfan_glue:
	- type: polygon
	points:
	- ref: matrix_inner_bottom
	shift: [0.5 kx + 0.5px, -0.5 ky + 0.5 py]
	- ref: thumbfan_far_thumb
	shift: [0.5 kx - 0.5px, 0.5 ky + 0.5 py]
	- ref: thumbfan_far_thumb
	shift: [0.5 kx - 0.5px, -0.5 ky - 0.5 py]
	- ref: thumbfan_near_thumb
	shift: [-0.5 kx + 0.5 px, -0.5 ky - 0.5 py]
	- ref: matrix_pinky_bottom
	shift: [0.5 kx - 0.5 py, -0.5 ky - 0.5 py]
	- ref: matrix_pinky_home
	- ref: matrix_inner_home
	patch_outer:
	- type: polygon
	points:
	- ref: matrix_ring_top
	- ref: matrix_ring_bottom
	- ref: matrix_pinky_bottom
	shift: [-0.5 (kx + px), 0]
	- ref: matrix_pinky_top
	shift: [-0.5 (kx + px), 0]
	patch_inner:
	- type: polygon
	points:
	- ref: matrix_inner_top
	shift: [0.5 (kx + px), 0]
	- ref: matrix_inner_bottom
	shift: [0.5 (kx + px), 0]
	- ref: matrix_index_bottom
	- ref: matrix_index_top
	controller_area:
	main:
	type: rectangle
	anchor:
	ref:
	- matrix_inner_top
	shift: [0 kx, -4.05 ky]
	size: [32, 76.5]
	corner: px
	switches:
	main:
	type: keys
	side: left
	size: 14
	bound: false
	keycaps:
	main:
	type: keys
	side: left
	size: [kx, ky]
	bound: false
	corner: 1
	keywell:
	main:
	type: outline
	name: raw
	patch_inner:
	type: outline
	name: patch_inner
	operation: add
	patch_outer:
	type: outline
	name: patch_outer
	operation: add
	thumbfan_glue:
	type: outline
	name: thumbfan_glue
	operation: add
	base_outline:
	main:
	type: outline
	name: keywell
	controller:
	type: outline
	name: controller_area
	operation: add
	screw_holes:
	top_left:
	type: circle
	anchor:
	- ref: matrix_ring_home
	shift: [-0.5 kx, 0 ky]
	radius: 1.05
	bottom_left:
	type: circle
	anchor:
	- ref: matrix_pinky_bottom
	shift: [0.5 kx, 0]
	radius: 1.05
	top_right:
	type: circle
	anchor:
	- ref: matrix_inner_top
	shift: [-0.5 kx, 0]
	radius: 1.05
	palm:
	type: circle
	anchor:
	- ref: matrix_index_bottom
	shift: [0, -1.06 ky]
	radius: 1.05
	thumb:
	type: circle
	anchor:
	- ref: thumbfan_far_thumb
	shift: [-0.55 kx, 0]
	radius: 1.05
	mounting_holes:
	$extends: outlines.exports.screw_holes
	top_left:
	radius: 2.05
	bottom_left:
	radius: 2.05
	top_right:
	radius: 2.05
	palm:
	radius: 2.05
	thumb:
	radius: 2.05
	bottom_outline:
	main:
	type: outline
	name: base_outline
	screw_holes:
	type: outline
	# TODO use footprints with pad + via reinforcement as mounting holes
	name: screw_holes
	operation: subtract
	plate:
	main:
	type: outline
	name: keywell
	switches:
	type: outline
	name: switches
	operation: subtract
	mounting_holes:
	type: outline
	# TODO use footprints with pad + via reinforcement as mounting holes
	name: screw_holes
	operation: subtract
	pcb:
	main:
	type: outline
	name: base_outline
	mounting_holes:
	type: outline
	# TODO use plated through hole footprints as mounting holes
	name: mounting_holes
	operation: subtract
	pcbs:
	top_plate:
	# include JLCJLCJLCJLC text somewhere
	include_keys: false
	outlines:
	edge:
	outline: plate
	layer: Edge.Cuts
	footprints:
	jlc_order_number:
	type: text
	anchor:
	ref:
	- matrix_ring_home
	shift: [-0.25 kx, 0.5 ky]
	params:
	text: "JLCJLCJLCJLC"
	justify: left
	bottom_plate:
	include_keys: false
	outlines:
	edge:
	outline: bottom_outline
	layer: Edge.Cuts
	board:
	outlines:
	edge:
	outline: pcb
	layer: Edge.Cuts
	# TODO there's a way to add stuff to the silkscreen layer
	footprints:
	mcu_l:
	type: promicro
	params:
	orientation: up
	batteryPins: true
	anchor:
	ref:
	- matrix_inner_top
	shift: [20, -11]
	rotate: 270
	mcu_r:
	type: promicro
	params:
	orientation: down
	batteryPins: true
	anchor:
	ref:
	- matrix_inner_top
	shift: [22.5, -12.25]
	rotate: 270
	pad_plus:
	type: pad
	anchor:
	ref:
	- matrix_inner_top
	shift: [23, -18]
	rotate: 0
	params:
	front: true
	back: true
	width: 1.5
	height: 1.5
	text: "B+"
	nets:
	net: Braw
	pad_minus:
	type: pad
	anchor:
	ref:
	- matrix_inner_top
	shift: [23, -15]
	rotate: 0
	params:
	front: true
	back: true
	width: 1.5
	height: 1.5
	text: "B-"
	nets:
	net: Bminus
	trrs_l:
	type: trrs
	anchor:
	ref:
	- matrix_inner_bottom
	shift: [32, -15]
	rotate: 270
	params:
	reverse: false
	symmetric: false
	# The naming of the nets on this footprint is different from the Corne schematics.
	nets:
	A: ""
	B: VCC
	C: GND
	D: P0
	trrs_r:
	type: trrs
	anchor:
	ref:
	- matrix_inner_bottom
	shift: [32, -13]
	rotate: 270
	params:
	reverse: true
	symmetric: false
	# The naming of the nets on this footprint is different from the Corne schematics.
	nets:
	A: ""
	B: VCC
	C: GND
	D: P0
	jumper_l:
	type: jumper
	anchor:
	ref:
	- matrix_inner_bottom
	shift: [23.5, 0]
	rotate: 270
	params:
	side: B
	nets:
	from: Braw
	to: Bplus
	jumper_r:
	type: jumper
	anchor:
	ref:
	- matrix_inner_bottom
	shift: [23.5, 0]
	rotate: 270
	params:
	side: F
	nets:
	from: Braw
	to: Bplus
	slider_l:
	type: slider
	anchor:
	ref:
	- matrix_inner_bottom
	shift: [30, 0]
	rotate: 270
	params:
	side: F
	nets:
	from: Braw
	to: Bplus
	slider_r:
	type: slider
	anchor:
	ref:
	- matrix_inner_bottom
	shift: [30, 0]
	rotate: 270
	params:
	side: B
	nets:
	from: Braw
	to: Bplus
	reset:
	type: button
	anchor:
	ref:
	- matrix_inner_bottom
	shift: [17, 0]
	rotate: 270
	params:
	variant: 2_pin_th
	nets:
	from: GND
	to: RST
	info_l:
	type: text
	anchor:
	ref:
	- matrix_pinky_bottom
	shift: [0.75 kx, 0]
	params:
	text: "samoklava v0.1\\nby soundmonster"
	justify: left
	info_r:
	type: text
	anchor:
	ref:
	- matrix_pinky_bottom
	shift: [0.75 kx, 0]
	params:
	layer: B.SilkS
	text: "samoklava v0.1\\nby soundmonster"
	justify: right mirror